Jump to content
SAU Community

Recommended Posts

After greatly annoying my neighbours for the last 2 hours(Gotta love a 3.5" exhaust with only a 4.5" cannon) i think i got a good compromise between idle and cruise.

Towards the end my battery voltage dropped from around 13.8 to 13??? must need some better earthing as i have already replace the altinator(Hes me hoping i dont need to do that again)

The voltage drop caused it to run alittle leaner(I think) around 15.2 and the odd stall pulling up after a short drive(Car always had this problem, could be no BOV??)

On boost she sat at around 11.2 which is better than the reported RICH from the techedge 2J1

So i think im getting somewhere finally, now for the big test driving to work YAY!!

  • 2 weeks later...

Ok so pretty sure i have an electrical problem. The longer the car runs the worse it gets. Had to drive from Mindarie back to work in West Perth today and about 10km's from the city it started leaning out to 18-19afr on cruise, had been running pretty much stoich on cruise for most of the way. Had to drop her back a gear and keep the throttle on a bit more to get her back to work at a more reasonable 15.5-16afr.

Drive it home 3 hours later and it was fine most ofthe way untill again it started leaning out.

A new Deatschwerks 300LPH fuel pump has been installed so i doubt its a fuel pressure problem.

Also after running for a while it starts missing alot at low rpm. It's bad enough to make it look like i can drive a manual when in first gear unless i floor it, it will lurch forward in time with the missing

Im thinking a number of things could cause this.

Stuffed CAS

General wiring/altinator problem(Voltage drops the longer you drive it)

Coil packs are packing it in(Dosnt explain the lean out, would appear to richen up if anything)

Any combo of the three above

Any input would be appriciated.

Using NB sim from my techedge wideband. Using an rb20 ecu so i dont think there is any learning going on

I can tell you that there will definately be AF trims learning on your car. You cannot tune a factory ECU without reading fuel trim data!! Fullstop..

How can the ecu learn if memory is cleared when the car is turned off? Pretty sure the rb20 ecu does not have any battery backed/NV RAM

Can %100 garuntee that there is af learning from CA18 onwards. If you have a factory manual goto pg EN-267.

You need to see this data to understand whats going on. Havn't used nistune - but surely it willgive you AF trim data.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...