Jump to content
SAU Community

Recommended Posts

hi guys,

here i have my 1994 R33 GTST for sale $18,500 ono make me an offer i cant refuse . it has just had a new custome pearl maroon paint job, and recently rebuilt and forged by EFI on the gold coast. i need to sell this due to the fact my fiance and i are moving to melbourne in 2 months now and dont want to take it down there.. this car is for serious buyers as it is very quick powerful and dangerous to the inexperienced driver.

it is still registered and can supply road worthy if needed. the car just has a 1000km done on the new motor as its just run in after the new build . dyno sheet can also be supplied, here are some of the following done

Engine mods:

plazmaman plenum

plazmaman throttle bodie

alloy radiator

ARP rod bolts

ARP head studs

ARP main studs

ACL bearings all round

CP pistons

H beam rods

tomei cams

new valves and springs

new valve seats

head port and polished

block honed

balanced and linished RB25 crank

new hoses

new alternator

new powersteering

splitfire coilpacks

brand new GT30/82R garret supplied by MTQ brisbane

link computer

custom painted engine covers and timing cover (not in picture)

custom catch can with speed flow fittings, done by EFI also (not in picture)

interior:

autometer gauges and tacho

APEXI AVCR boost controller

HKS turbo timer

mongoose M80G alarm

sparco gear knob and boot

momo race steering wheel

cutom carbon fibre dash

Bodywork:

Do-luck front bar

custom side skirts have just been done(not in picture)

brand new custom skyline maroon paint job with pearl

so guy's make me an offer and i will consider it

. please feel free to pm me or text 0458924408, thanks sam and katrina

Link to comment
https://www.sau.com.au/forums/topic/372385-r33-rebuilt-forged-rb25/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...