Jump to content
SAU Community

Recommended Posts

Hi people

I got some 18'' mags with pretty close to new tyres on them. less than 200km on the tyres.

235/40/R18 Zetum tyres all around

Selling because I was told these mags came off an R33 - failed to mention I would need a 5mm spacer and to flare the front guards to make them fit.

so now I just want to recover mostly the cost of the tyres so I can get some new tread on my stock rims.

I don't know much about wheels, so I cannot offer any offset insight - there are some numbers inside the mags I could get a photo of if anyone thinks they might be the offset figures.

I'm pretty sure they'll need a balancing - can see where some of the little weights have come off already.

I'd like to get $800 for the mags/tyres - open to reasonable offers.

IMG_2011.jpg

IMG_2008.jpg

IMG_2010.jpg

IMG_2009.jpg

IMG_2014.jpg

Enquiries via PM or call/sms Raven on 0404-482-847

Link to comment
https://www.sau.com.au/forums/topic/380605-cheap-18-mags-fresh-tyres/
Share on other sites

Found the thread I got these tyres from -

where they were listed as:

JDM Deep Dish 18 inch Mags (Rear: 18x9.5)

If my memory serves correctly the fronts aren't as wide as the rears - I wanna say 8.5, could have been 8 (tyre monkey told me amidst a bit of a ramble)

Bump

Any offers at all - I'd consider trading for stock rims with good rubber or something to that effect

I'd even consider trading for fmic setup for r33 + cash my way, or cat back exhaust + cash my way (assuming sub $500 value)

don't be shy, I'll consider any offer

the back wheels fit an R33 perfectly

the front wheels need a 5mm spacer (illegal) and maybe some guard work.

I drove it for about 2 hours in total with the front wheels on - there's this corner in front of my drive-way which causes something to scrub somewhere around the front passenger wheel - I'm not sure if it's the tyre scrubbing on the guard or if my front bar was hitting the road, my driver side guard has been flared a tiny bit from a small ding just below the headlight and the scrubbing never happened on that side, so it could be something as easy as that.

You're welcome to come have a look, I'd be happy to put them on the car and show you exactly what scrubbing I'm talking about.

the back wheels fit an R33 perfectly

the front wheels need a 5mm spacer (illegal) and maybe some guard work.

I drove it for about 2 hours in total with the front wheels on - there's this corner in front of my drive-way which causes something to scrub somewhere around the front passenger wheel - I'm not sure if it's the tyre scrubbing on the guard or if my front bar was hitting the road, my driver side guard has been flared a tiny bit from a small ding just below the headlight and the scrubbing never happened on that side, so it could be something as easy as that.

You're welcome to come have a look, I'd be happy to put them on the car and show you exactly what scrubbing I'm talking about.

i wish i could but im in townsville

Number from inside the front mags:

30

18x8

and I can't be stuff taking the back wheels off to check them

PRICE DROP $800 Now $700 ono

Edited by Raven33

I'm not sure how they would go on a 34 - you're welcome to come over and see if they fit.

Here is a link to a forum thread about wheel sizes & offsets for Skylines - if what I think are the offset details on the front mags is correct then there's a good chance they'll fit

As for painting them, there are some guides in the DIY section that cover painting mags - doesn't seem to be too hard a job, more a test of patience

Here is a link to a guide on these forums.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...