Jump to content
SAU Community

E.o.i/swap/for Sale Rb26Dett New Garrett -5S Complete Setup

trustr32
 Share

Recommended Posts

trustr32 Rising Star

trustr32

Posted
Posted

Hi Guys I have just spent the last 2 years building up my R32 GTR and bought everything to run twin Garrett 2860-5's. This setup has NEVER been used other than 10-15 minutes of running at idle. The car hasnt been driven so it is as new. I had to remove my engine again yesterday and have decided I want to go single instead of sticking with the twins. So I want to sell/swap this setup. Everything is made for a 32 but would probably fit 33 as well.

Kit includes:

-Brand new Garrett 2860-5's only run for 20 minutes MAX at idle x2

-Custom stainless low mount stock position manifolds x2

-Xforce split stainless dump pipes bought second hand but in excellent condition also heat wrapped x2

-Stainless y-pipe I think it's 2.75 into 3.25 but i'll check

-Complete custom 3 inch stainless piping turbo's to airflow metres to stock blowoff valve hard pipe

-Custom 3 inch alloy pipe from twin turbo pipe to cooler

-Factory 2 into 1 twin turbo pipe

-All oil lines, water lines, oil drains, metal gaskets, silicone joiners, clamps etc. full bolt on package.

The manifolds we're made By Ryan Capel from Capel motorsports and are of the best quality stock position low mount manifolds around. The only other car with these manifolds is the car that used to be known as "TWOOGLE" My mate did all the piping and it looks really good in the engine bay I have only shitty just jap mushroom filters on at the moment but the piping was made with the 150mm hks mushroom filters in mind.

I'm looking to put on a high mount GT35/40 on it so if anyone out there is thinking of swapping back to twins then hit me up and we could work something out.

I know I'm obviously not gonna get all my money back but I'd like to offset most of the cost so I'm looking for around $3400.

post-58307-0-57237400-1351235227_thumb.jpg post-58307-0-00974600-1351235346_thumb.jpg post-58307-0-38088200-1351235372_thumb.jpg post-58307-0-45103200-1351235424_thumb.jpg post-58307-0-60614400-1351235442_thumb.jpg post-58307-0-52281600-1351235461_thumb.jpg post-58307-0-71891300-1351235483_thumb.jpg post-58307-0-28530900-1351235503_thumb.jpg post-58307-0-58251800-1351235527_thumb.jpg post-58307-0-80420600-1351235654_thumb.jpg post-58307-0-10704800-1351235760_thumb.jpg post-58307-0-51992900-1351235776_thumb.jpg post-58307-0-32450200-1351235796_thumb.jpg post-58307-0-56913100-1351235816_thumb.jpg post-58307-0-65826900-1351235838_thumb.jpg post-58307-0-68145100-1351235884_thumb.jpg post-58307-0-77072700-1351235906_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • patrickxdf12
      Squeaking clutch/throw out bearing

      By patrickxdf12 · Posted

      Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Murray_Calavera
      WTAC 2025

      By Murray_Calavera · Posted

      Yeah mate, never miss it.
    • Ozdavroz
      WTAC 2025

      By Ozdavroz · Posted

      Any going to watch World Time Attack at SMSP this year?
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...