Jump to content
SAU Community

Recommended Posts

Don't be scared to use it

Ive mentioned before that I had already done the cleaning but am still having the issue therefore I asked in a thread with someone else with the same issue. Infact, I used that very article as a guide.

The second question was which plug was for the TPS, since that article has only 1 plug where as my R33 has 2.

Thanks for the contribution though. :rolleyes:

For mine, they both have cables. I've read that the grey is for auto's but mine's a manual. Perhaps the grey cable isn't connected further down the loom but at the plug, its definitely connected.

Maybe. I've only had the car for a few months. Its got a proper manual gearbox and the gauge cluster is for a manual too. Anyway, so a manual shouldn't have that plug and so its the other brown one. Is there anything else that can cause the rough idle? The revs dont change that much, only like 50-100prm, its more the car shakes. Its not O2 sensor as I disconnected that and still had problems. Revs are adjusted properly because i just disconnected both the grey and brown cable and couldn't get the revs to drop any further than 1000, the screw in AAC is all the way in. I just want to make sure that its nothing major.

Edited by shubby0901

My boost gauge piping had split (for the second time) so I fixed that although I doubt that'll cause the air-con issue.

My car has not buttons or anything inside. The only sign of an auto car are the two plugs on throttle body. Maybe they installed a auto throttle body? Not sure but yeah inside the car, there are no signs unless I'm missing something very subtle.

Havnt had a proper chance to test but initial impressions are that the shaking is alot less violent....so im assuming this vaccum leak could be a factor. Unplugging any sensors had no effect...testing shall continue

  • 3 weeks later...

btw, ive seen quite a few series 2 manual skylines with the 2 plugs on the throttle body...maybe all series 2's have it?

edit: there are series 1 auto skylines with 1 plug...i think it may be a series vs 2 thing rather than auto vs manual?

Edited by shubby0901

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...