Jump to content
SAU Community

Recommended Posts

:P Due to financial reasons i need to sell my line, for a house urgently.

Need to sell this by next weekend

1993/94 R33 GTS-T M SPEC (Original)

2.5L Turbo, DOHC, 24 VALUE

Manual transmission with short shift

Metallic Silver

Low KM

Mods:

- Pivot Turbo Timer

- Black Widow Paging Alarm with Immobilser and Central Locking (1Km Paging)

- FULL BODYKIT - Gtr Veilside Front Bar/ GTR Grill / GTR Rear Bar & Side Skirts & gtr rear pods

- Standard R33 Cluster with white EL dials (Blue/Green at Night)

- Custom Silver Dash Surround

- Sparco Gear and Handbrake Knob

- Boost Gague - Blitz Racing 2.6 Bar Boost Gauge with Autometer Pilar Mount

- Custom GTR Style Front Mount Intercooler - Twin end tanks

- Wheels - 17'' Chrome wheels

- Tinted Windows

- Blitz Duel Drive BOV

- Boost Controller Value set at 12PSI

- Snap on seat covers

- Oil Catch Can

- Nismo Heat Shield and Simota - Air Filter POD

- 3'' Dump Pipe / 3'' High Flow Cat / 3'' Cannon muffler with 5'' Tip

- Cusco Front & Rear Sway Bar

- Custom Number PLATES - Not Included with car

- Standard Jap Stereo System

$20,000 with the above. No RWC will be provided as i work 6 days a week but should be roadworthy with the silencer for the exhaust.

Extra Mods for $2K - Gives you a 13' second 1/4 mile

- Apexi Power FC

- GReddy Profec B II - Boost Controller

- Nismo 320km Dash

Very regretful & genuine sale.

Contact me via my Phone Number (BH), 0412402283.

Link to comment
https://www.sau.com.au/forums/topic/43860-quick-r33-gtst-gtr-veilside-kit/
Share on other sites

bump is a message to move the thread to the top of the first page. The red hoses are connected to the oil catch can going into the engine again.

more pics available just pm or post reply with your email address.

cheers

ak

two questions. im new... what doesn BUMP mean in posts

and what are those red hoses in your engine bay doin? going to?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...