Jump to content
SAU Community

Recommended Posts

Genuine Gizzmo MSIB-C v3 Electronic Boost Controller (53PSI)

QUICK SUMMARY

Gizzmo’s MSIBC has been on the street now for approximately 10 years and has the glory of being John Bradshaw’s choice on his 7.45sec 187mph GTST Skyline.

Albeit the best value controller anywhere, the MSIBC-V3 uses a genuine American MAC solenoid and a precision Motorola pressure sensor. All the critical hardware components are high precision and quality branded items.

In it’s initial design we purpose built an engine setup so we could fine tune the boost control on our hub dyno up to the advertised 3.5 bar; we ran it up to 53 psi to be exact (3.65bar). At that level we were getting fluctuations of +/- 0.3 psi on the test mule, so approx 1%.

This control software still resides at the heart of the MSIBC-V3 although everything around it has been improved. The processor is now 16bit instead of 8bit. Physically it is 80% smaller and 70% lighter (with bracket) than previous versions. Now, to make mounting easier, it has a mounting bracket, also we have now added a feature that allows you to quickly set up your boost, even in real time whilst on boost if you’re feeling a little crazy.

So like most of todays technology, the MSIBC-V3 is easier to use, lighter, smaller, more powerful than ever before yet still costs the same. We challenge you to find a better value boost controller anywhere in the world!

FEATURES

NEW for V3 Easy set Boost feature

NEW Reversible adjustable mounting bracket

NEW Tiny Profile (57mm x 26mm x 30mm)

NEW Weighs approx 40g with bracket

Remote Scramble/Memory Change (Yellow wire to earth)

Simple 2 wire installation

Open and Closed loop boost control

Closed Loop Solenoid Supervisor

Operating Current < 0.5A

Reverse Battery Protection

6 Boost Memories

32mhz 16bit RISC Processor

Active Over Boost 5psi to 50psi

White 7 segment LED display

White backlit buttons

Real Time digital boost gauge

Pressure Display in PSI, BAR or KPA

Suits Internal or External Wastegates

Comes complete with High Performance MAC Solenoid & All Fittings

ONLY $290 incl. Delivery (Express)

MS-IBCv3%20_350.jpg

BUY_BUTTON.gif $290 Delivered

  • 3 weeks later...

With more functionality then the eBoost Street and same MAC solenoid as the eBoost2 these have proven to be fantastic HP-4-ur-buck!

:yes::yes::yes:

  • 1 month later...

Same guys...

... Knock monitor set-up also available.

Introducing the K-Lite>

Gizzmo's K-Lite signifies a new evolution in engine protection. With 11 frequency & gain settings, 6 knock display levels, peak recall and housing 2 processors dedicated to protecting your investment, you know exactly how close (or over) the limit you are. The accuracy of the KMon in the size of a shift light.

  • 1 month later...
  • 2 months later...
  • 1 year later...

This is hand's down the best value for money electronic boost controller on the market today - Australian designed unit's.

Make use of the same USA solenoid as Turbosmart.



  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...