Jump to content
SAU Community

Recommended Posts

Hello everyone, up for sale is my Pearl White Jap Spec 99 Nissan Silvia S15 SPEC R, This car has my pride and joy Due to unfortunately my circumstances has changed and now I have to redirect my resources elsewhere. The car has plenty of modifications , it always been filled up with BP Ultimate 98 octane. The gearbox is nice and tight as new! Mechanically A1, Modication to list:

-IMPORT MODEL

-RENEWED 12 MONTH REG NO RWC

- Full Authenic Jap Spec Aero Kit (besides wing)

-118,xxx on the clock

-Fresh rebuild from previous owner (metals gaskets, new seals etc etc) 40 thou since

-Greddy turbo timer

-Hks electronic boost controller

-Greddy engine pulleys

-Aftermarket Engine damper

-Greddy intake pipe

-Apexi Pod filter

-Front Mount Intercooler

-Braided oil lines

-Walbro Fuel Pump

-Hks radiator cap

-FULL 3inch turbo back blitz nur spec exhaust

-Nistune ecu

-Tuned at chasers 220kwatw

-HD Excedy Clutch

-New Fully Adjustable BC Coilovers

-Aftermarket Front Tension Rods

-Aftermarket Front Control Arms

-Aftermarket Rear Toe Arms

-Aftermarket Rear Camber Arms

-Panasport g7's 17x9.5/9 wrapped in brand new Ku31's

-Pioneer Headunit AUX

-Alpine Tweeters/ Speakers

-Custom old style apexi 60mm gauge on stock a pillar

-Nismo GearKnob

-Carbon Fibre Style Shift boot/ Handbrake boot

-Clear Side Marker Indictors

-Shaved Fiberglass Boot lid (doesn't align too well)

-Tinted Windows

-Factory Visors

-Original Log Books From japan

-Extras (Yahio Factory Tailights + Nismo Catback)

-Comes with factory airbox + intercooler + stock suspension

There is no financial money owing on the car and there is no written off status on the car

Please no time wasters, tyre kickers and definitely NO SWAPS as I have a daily A to B car. This car IS 15 years old so do not expect it to spanking brand new so expects few scruff marks and dings (sale price reflects this). A photocopy of your licence will be required for a test drive; this is for my own protection as a seller.

All the paper work required to transfer the car to under the new owner will be completed prior to sale this will ensure a easy and smooth process both me and the new owner.

- Vicroad's transfer paper

- External contract written confirming the sale both signed by both parties (seller and buyer)

Personalized plates / Bride seats are not included as they where a gift

Thanks for viewing

price: $16,900

Name: Cuong

Post Code: Brooklyn Vic 3012

Mobile Phone: 0411 511 917

post-52105-0-04426800-1411034537_thumb.jpg

post-52105-0-80945600-1411034551_thumb.jpg

Edited by Mr.Izzy
Link to comment
https://www.sau.com.au/forums/topic/448768-2000-nissan-silvia/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...