Jump to content
SAU Community

Recommended Posts

(once again the classifieds has been changed around and the "New Classifieds" is gone... so i will post it again)

Seems that im going to be selling the Ceffy without these wheels so theyre up for grabs.

Awesome rims with some nice dish on the rears and a little dish on the fronts. The center caps on them say STICH GULF, but i cannot find anything on this brand... in english. They look exactly like the Altstadts and even the markings inside the rim and the sticker used is identical. So im not sure if STICH is a shop in Japan that rebadges them or what. All i know is that they are a hot looking rim.

No idea what the exact specs are on them, all i know is the following.

Brand: Stich Gulf (Altstadt?)

Model: 1

Size: 18inch

Widths: Unknown (if i had to guess i would say 10 inch rears and around the 8.5 inch front)

PCD: 114.3

Offset: Unknown

Front Tyres: Worn on the outside

Rear Tyres: Low tread (not rwc passable)

ceffy4.jpg

ceffy4f.jpg

ceffy5.jpg

1.jpg

Wheels are currently on a Nissan Cefiro with either a 300ZX or R33 GTST 5 stud upgrade using rather large spacers.

Priced the Altsdadt 1s new from Donnellans and theyre 1045 per rim WITHOUT tyres.

Theyre in pretty good nick considering they came off a dori car. Minor scrapes. I will take some photos of them tomorrow and put them up.

Looking for around the $2500 mark.

Call Ni (KNEE) on 0422 930 505

or email at [email protected]

No time wasters, genuine offers considered... im not interested in talking to people looking for something for nothing.

confirmed theyre +35. Should fit most skylines.

will have hi res up close pics later once the battery pack is charged.

checked the backs and theyre JAWA so not original ALDSTADTs or however its spelt.

They brand is STICH which is from the JAWA corporation (i think lol)... hard to find info on em... but they arent even cheap in japan...

Cheapest STICH 18x9s i could find were over 70,000yen + tax... so almost a grand each... but then u have to send em to australia... thats where they get expensive... so if u wanted to import a set as they arent available in australia as far as i can find they will end up being more expensive then the alstdatsor whatever theyre called... the 18x10s werent even listed with a price.

As for dish.. no idea... maybe 3/4 an inch front and 1 and a half back... i'll measure it tonight.

oh... more pics are uploaded in my galerys main page if u wanna see the scuffing on the front rims

ok if it fits skylines im definitely interested,  

pm or add a post up

and ill come meet up with ya have a look

email me... u can come have a look this weekend if u want.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...