Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

pete will you be licenced with gtrrr on tha road by then?

damono your ride out of shop?

if yas wana avoid mandurah can set meet point near my place in barragup ( ie barragup hall)

sooooooooo this tuesdy or next?

my car is still @ ginos panel and paint. hopefully get it back by the weekend. Apparently they're waiting on a new 400R rear bar, was supposed to be done by today.

If i get it back.. i wouldnt mind coming down, but i have no idea where barragup is

ooo pete wont be there in time... :rant:

we can have another one straight after and i can gaurantee alot of people there.... if you guys are keen

ps. barragup hall is a good place to meet....

damo.... head down to mandurah and turn left at the forum lights up pinjarra road... and you will see and ampol (i think) on the left.... there is a hall on the right.... plz confirm gav...

yea fane you where pretty much right cept they tore down the ampol at end of my street like 1.5-2 years ago but i still tell the taxi to let me of at the old ampol cervo

see yas all there tuesdy then 6ish?

post up if yas comin ay

(edit) we do a petes got his licence back cruise in near future as well

hahah I MISSS the cruising with you guys.

I luckily slipped away from the police for 3 years in Mandurah. Black/dark cars are like Phantoms, they get less attention at night. If my skyline was like White like Ashs car, they wudve had a field day on me.

Rule of thumb is to not speed/make noise on Pinjarra road. I know I did, but anyway, its not good.

I miss those days of Random cruising, our impromptu Wet weather meets, Ahh good old "be there in 10 mins at Gull" meets. Bunky cruising, rallying.

I need to move back to Perth BADDDD.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...