Jump to content
SAU Community

Recommended Posts

Brand new garrett GT Series BB turbo rated at 500hp. This is also

known as the GT30R 56T model

Front A/R is 0.6 (clears headers and Engine mount!)

Rear A/R is 0.82

4'' inlet with massive bell mouth to suck in plenty of laminar air

with surge shroud (similar to HKS 3037S)

2" outlet to suit intercooler pipe work

Turbine housing: GT30 non wastegated.

Inlet: T3

Outlet :GT30

Ball bearings allow the turbo spin forever, even when spun by hand and increadible reliability on high boost. I have seen these making 300 Rw kw on 17 PSI!

Item includes Garrett warranty from date of purchase.

Unlike bushed (STD wet floating bearing) turbos that need replacing/rebuilding

at 40,000 klm in performance applications, this will only require new oil seals

at 80,000 klm. This means long term savings!

Utilizing the latest compressor and turbine wheel design these have proved to

spool up even faster providing more drivability, stronger midrange power and torque with better reliability.

Inconel turbine shaft which is extremely light allowing quicker turbo response

and heat resilient this turbo is top shelf with no expense spared.

Recommended retail is $2960

Turbo only $1799

____________________________________________________________

HKS Cast manifold.

This will not crack! In addition it can be further ported, extrude honed etc for further improvement if need be. As you can see from the pic's, the design is pretty good. All runners are split as far up to the collector as possible which will give good top end and mid range performance. It even splits the wastegate gasses.

This has a T3 flange, but is big enough to be drilled for a T4 flange if required.

I usually use these with GT30/35/40 BB turbo's due to the T3 flange. Due to the low mount design, you minimize any unwanted attention from the cops! If you need more info feel free to Pm me.

ON HOLD

c2_1_b.JPG

50_1.JPG

e5_1.JPG

b8_1.JPG

d1_1.JPG

1b_1.JPG

____________________________________________________________

Brand new HKS Style wastegate to suit.

45mm Valve, silicon/nomex doaphram and 12 psi spring

$250

There is no warranty on this wastegate as I got it cheap and am selling it for what cost. It is NOT an original HKS wastegate (otherwise it would be $1300)

____________________________________________________________

Manifold and Turbo combination $POA

RB25DET Nismo 550 cc injectors $750 cleaned and shipped

RB20DET/RB26 HKS 550cc injectors $750 cleaned and shipped

ff_1_b.JPG

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
    • So 10/10 times that code is coil packs? I mean if that's the case ill drop the $400USD or so to replace them. I didn't know these cars threw codes before the issue became an issue.
×
×
  • Create New...