Jump to content
SAU Community

Recommended Posts

Updated price: $7,500

Updated with pictures

Has 102,000km on the clock

Is a stock standard RB25DET and gearbox and clutch and driveline

Interior drivers garnish and air con vents are damaged, have a new one here

Diff provides no drive, I assume the drivers side halfshaft has been pulled out of the diff.

Needs a rear quarter cut, drivers side suspension subframe and drivers door. A-pillar is unharmed. B-pillar needs a little straightening where the drivers side intrusion bar bent it backwards about a centimetre.

Bootlid is fine but now needs a little touchup paint on the edge because the rear quarter is touching the bootlid and the hinge of the bootlid is pushed about 1cm in, therefore the boot doesn't shut properly.

From a couple of us checking the car out, we *dont think* the subframe is bent but still could be by an unnoticeably small amount.

Needs a new wheel and rear caliper assembly, they were broken as part of the accident.

The engine and gearbox stock standard and are perfect, the owner was a big wuss when it came to thrashing cars.

Car has no rego, registration has been cancelled. There are no debts on it either. It is fully complied under low volume system, been in Australia for a few years with the one owner.

Click each picture for a large version

01.JPG

02.JPG

03.JPG

04.JPG

05.JPG

06.JPG

07.JPG

08.JPG

09.JPG

10.JPG

11.JPG

12.JPG

13.JPG

14.JPG

15.JPG

Sorry, only going from memory. Will get more details in the next few days

Approx 100,000km

5 speed manual (as per thread title)

I think its a 1993 model

No mods

Fully owned and complied (green plates), no rego.

Interior in very good condition

Comes with some spare parts

Bootlid is OK, rear bumper and RHS taillight needs replacing

Front bumper needs a respray

Otherwise the car is in very good condition

  • 1 month later...

Nar not drift damage. Sitting on Middleborough Rd waiting to turn right and an unlicenced driver with no fixed address driving someone elses unregistered car slammed into the skyline :P

Hey mate,

Have you looked to see what a 1993 GTS-T goes for? And in repairs and damage there is easy $4000-5000 so why would someone go through all that to save $3000 and know they bought a damaged car. I will offer you $2000 cash as long as you are willing to provide all vehicle details for a Revs Check

G

Hey mate, you are VERY funny.

This car may also be used for wrecking. Have you priced up a halfcut lately? How much do you think an rb25det engine alone goes for?

$2000 hahahaha.

Do you really have nothing better to do than post rubbish in other peoples threads? If you're not going to buy it then get lost, I nor anybody else is interested in hearing your drivel.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
×
×
  • Create New...