Jump to content
SAU Community

ringgear stopper??

Godzilla32

By Godzilla32,
in General Maintenance

 Share

Recommended Posts

Robbo Enthusiast

Robbo

Posted
Posted

I used loctite on mine, as I couldnt click it off at 330ft/lb. I sparingly used loctite supernut lock which is the lower grade blue type.

I'd advise against using stud lock (red) or the retaining compound (green). I've seen bolts permanently attached with these grades. Once I saw a coarse threaded bolt that wasn't that much larger than the balancer bolt which we couldnt undo. Not with a 3/4" rattle gun, not with an 1" rattle gun and not even with an 1" rattle gun that used an 1" air line!!!

Godzilla32 Veteran

Godzilla32

Posted
  • Author
Posted

Note to self: Only use BLUE loctite!!

I really dont see a point in replacing the crank seal as its not leaking and would be more trouble than its worth IMO.. I am however doing the camseals and half moons, replacing the tensioner and possibly the bolt for the tensioner and the stud for the idler. The idler itself feels very smooth so im thinking not to bother replacing it... Any input?

Cheers,

Deren

MARRIOTT Apprentice

MARRIOTT

Posted
Posted
Note to self: Only use BLUE loctite!!

I really dont see a point in replacing the crank seal as its not leaking and would be more trouble than its worth IMO.. I am however doing the camseals and half moons, replacing the tensioner and possibly the bolt for the tensioner and the stud for the idler. The idler itself feels very smooth so im thinking not to bother replacing it... Any input?

Cheers,

Deren

You're better off replacing the idler. You'll kick yourself if you have to pull the whole thing down again in 10000k's if the idler gets noisy. They're only about $70 - do it now or suffer the pain.

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Just posting these details as the search on this forum just sux now. Can't go past a couple of months.

BSC Motion Technology

3/ 1968 Hume Hwy Campbellfield VIC 3061

ph: (03) 9357 7515

Idler: NSK 56TB 2801 B01

Tensioner: NSK 60TB 0683 EA7L 806

Now I spoke to Steve when I got mine there and they were only about $120 for the pair. They apparently had hundreds in the warehouse.

Godzilla32 Veteran

Godzilla32

Posted
  • Author
Posted

Is it really important to torque the crank pulley bolt to exactly 446-466Nm?? Thats a huge amount of torque and the wrench needed would be very expensive. Im planning to buy a smaller one for lighter jobs but i cant even find some where to higher one like that. Someone said they just did it up as tight as they could, and it was ok. I'd prefer to torque it to the right tension but sounds as though it will be difficult...

Deren

wrxhoon Grand Master

wrxhoon

Posted
Posted
Is it really important to torque the crank pulley bolt to exactly 446-466Nm?? Thats a huge amount of torque and the wrench needed would be very expensive. Im planning to buy a smaller one for lighter jobs but i cant even find some where to higher one like that. Someone said they just did it up as tight as they could, and it was ok. I'd prefer to torque it to the right tension but sounds as though it will be difficult...

Deren

Yea you need a 3/4 drive torque wrench , i have one but i'm in Sydney otherwise i would lent it to you .

As long as you do it up very tight with a big bar it should be o.k. , i always do them up with a torque wrench though .

  • 3 weeks later...
Godzilla32 Veteran

Godzilla32

Posted
  • Author
Posted

Recently put the crank pulley bolt back in and did it up real tight, now i cant undo it to make changes! I didnt think id need to undo it so i did it as tight as i could. I've already broken about 3-4 breaker bars!! Can anyone help me to get this bastard undone?? :(

Thanks guys,

Deren :(

GTRgeoff Grand Master

GTRgeoff

Posted
Posted

Deren, maybe call lubemobile and tell them to bring a 3/4 rattlegun. Has to be worth paying for that. I have a heavy duty pulley pin spanner I made that should hold the load as well to make it easier and maybe you could buy a 3/4 breaker and socket.

I'd come and help but still recovering from back surgery.

Godzilla32 Veteran

Godzilla32

Posted
  • Author
Posted
Deren, maybe call lubemobile and tell them to bring a 3/4 rattlegun. Has to be worth paying for that. I have a heavy duty pulley pin spanner I made that should hold the load as well to make it easier and maybe you could buy a 3/4 breaker and socket.

I'd come and help but still recovering from back surgery.

Thanks again for the reply Geoff. Would a rattle gun fit in there with only the radiator removed?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Butters
      UniClutch

      By Butters · Posted

      Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...