Jump to content
SAU Community

FS Melb: Damaged R33 GTS25t manual Price drop $6500

Bozz
 Share

Recommended Posts

Bozz Proficient

Bozz

Posted
Posted

Updated price: $6,500

Updated with pictures

Has 102,000km on the clock

Is a stock standard RB25DET and gearbox and clutch and driveline

Interior drivers garnish and air con vents are damaged, have a new one here

Diff provides no drive, I assume the drivers side halfshaft has been pulled out of the diff.

Needs a rear quarter cut, drivers side suspension subframe and drivers door. A-pillar is unharmed. B-pillar needs a little straightening where the drivers side intrusion bar bent it backwards about a centimetre.

Bootlid is fine but now needs a little touchup paint on the edge because the rear quarter is touching the bootlid and the hinge of the bootlid is pushed about 1cm in, therefore the boot doesn't shut properly.

From a couple of us checking the car out, we *dont think* the subframe is bent but still could be by an unnoticeably small amount.

Needs a new wheel and rear caliper assembly, they were broken as part of the accident.

The engine and gearbox stock standard and are perfect, the owner was a big wuss when it came to thrashing cars.

Car has no rego, registration has been cancelled. There are no debts on it either. It is fully complied under low volume system, been in Australia for a few years with the one owner.

Click each picture for a large version

01.JPG

02.JPG

03.JPG

04.JPG

05.JPG

06.JPG

07.JPG

08.JPG

09.JPG

10.JPG

11.JPG

12.JPG

13.JPG

14.JPG

15.JPG

Bozz Proficient

Bozz

Posted
  • Author
Posted

pictures fixed

Diff isn't stuffed

The halfshaft was pulled out of the diff, I've welded up the supsension mounts and the car can now be driven, here are the repaired pictures:

r33a.jpg

r33b.jpg

  • 2 weeks later...
  • 5 weeks later...
  • 1 month later...
Bozz Proficient

Bozz

Posted
  • Author
Posted
wanna swap for a 91 VN Calais? :)

Does it do sik skidz bro?

cuz if my homies wont restecpa me if i can do skidz up chappz uleh

Seriously, the car left today, thanks for the offers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Duncan
      Chris' Toyota Mark ii JZX110

      By Duncan · Posted

      Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...