Jump to content
SAU Community

Perth Performance Shops Are Useful

uneekwahn

By uneekwahn,
in Western Australia

 Share

Recommended Posts

gtrken Grand Master

gtrken

Posted
Posted

Thankyou Jason, your reward will be in the mail... :starwars:

Seriously , all workshops can and do make mistakes, it's all part of the process and the idea is to find a shop who are experienced at working on your particular type of vehicle.

Talk to the shop , tell them what you want.

Some peoples expectations far exceed what the shop is capable/willing to do for the money people want to pay.

If you pay KMart prices, you will get KMart results...

Mods, I think this thread has run its course and should probably now be closed.

Ohh , and in answer to a certain member on this forum who is doing his best to discredit a couple of shops who put a lot into the Import car scene in WA , you may have your people who agree with you but I can assure you there are more who are saying your just a silly little boy...

Cheers

Ken

Link to comment
Share on other sites
jaik Mentor

jaik

Posted
Posted

Jason, you need a tissue to wipe the shit off the end of your nose :starwars:

But to add my useless 2c worth Id like to say Kens great when he does jobs for cartons because he drinks the shittiest cheapest Aussie beer money can buy!

JK

Link to comment
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • hardsteppa
      R32 OEM rims name?

      By hardsteppa · Posted

      That's some good input mate. Nice.
    • PranK
      My BMW 335i

      By PranK · Posted

      So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Jonesy93
      R32 vs R33 R34 C34 heater core matrix and elbow pipes info thread

      By Jonesy93 · Posted

      Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...