I8EE

sorry guys havnt checked this in ages! diff is from a turbo manual, R200 i believe?? 3.9 gearing. . . i have a auto non turbo one atm which is 4.36 ratio in the car. . . good for skids haha but im keeping that one

Anyone??

ive checked the following; Superspark igniter Check for cracks in coilpacks Check plugs/connections Clean afm Check cooler piping connections 02 sencer Fuel pump Leaking injector Crank angle sensor Fuel filter anything else i should check??

yes diff still for sale!

how about roof spoilers?? will two door ones fit? i dont mind cutting lol

bump! anyone. . .

looks good mate! what roof spoiler is that??

buy my four door

also got 5 spitfire coil packs and a standard one . . .

hi guys, took my car down the strip the other week and it was fine then on the last run it was going spastic and spluttering at about 4grand but if you take your foot off and punch it again it seems to be fine. . . car was tuned for 18psi and now its only hitting 12 and doing that rubbish. . . . ive changed over fuel pumps (had a walbro then put my mates new 044), swapped crank angle sensors and not sure what else to check. . . . i also changed the plugs too. . . stumped on what i need to check, so any ideas would be helpful! mods; 750cc injectors 3071r microtech ecu fmic 3" TB exhaust

sms sent

Hi Guys, Got a Bee*R Limiter for sale. . . 230 Including Postage anywhere in AUS. . . Sounds Sweet =) 0411 117 167

Cheers man will check it out! do you know where i can get a roof wing from? do you know if the two door ones fit???

Hi all, looking for a kit to put on my four door 32, so far i can only find vertex =S does anyone know of sites of anything where i can get one from?? im also wondering if a 32 two door roof wing would fit with some modification to it?? Cheers, Anth

cheapppp give me offers!

its a quite simple job, ive put them in my carbon bonnet just the other week. . . http://www.facebook....2b&id=683633649 i used a die grinder and notched it out slowly to get the right size, the pins actually have like a 5-8mm lip which allows it to cover the hole and screw into the bonnet with. . .

RB20det crank angle sensor 140 delivered

well ive got a microtech in mine atm, changed the injectors and had it tuned ran fine, now that ive gone bigger turbo and re-tune, the injectors? seem like they are cutting out at 6.5grand then come back in. . . would this be because there low impedance?? only asking because you have the high impedance listed as the ones for 32's. . .

for the r32's do the injectors have to be Hi-Impedance? ive got 700cc siemens low-impedance in my 32 atm . . .

Price drop 1) Jap cat-back system. 2.5" good condition, jasma approved. . . two muffler and nice round tip with slight splice back, good for defects $150 2) SOLD 3) Silver top Injectors RB20det x6 . $100 4) Standard R32 GTST Computer $70 5) Moulded mud guards. $40 6) GTST Spoiler in sky blue, with brake light? $40 7) Turbo LSD - 5 Bolt - $150 without half shafts 8) Bonnet cable set-up, with latch and interior puller. $20 9) 3" one piece dump pipe $110 10) standard t3 turbo, has shaft play. $80

what plugs are you running?? try bcpr7e or 6e plugs, should be pregapped to .8

still got front indicator corner lights?

ive got a microtech. so i connected the rpm tacho output to a wire which i ran to the tacho signal at the back of the cluster. fairly simple i thought, but the tacho still isnt working? just a thought but, does the tacho need resistors or anything in the line???

Perfect! thanks heaps dude

Hi All, I'm looking for info on the cluster, specifically what the wire pin outs are. Basically I need to know what wire does what leading from the harness on the back of the cluster. Ive been scouring the net for some thing but I've had no luck. mostly, i need the RPM signal wire off the cluster. . . need to hook it up from there, back to my ecu. . . Any info would be greatly appreciated. Thanks in advance.