import_zone

spotted the old's driving on lower north east rd around 4.15 this afternoon

spotted the old's driving on lower north east rd around 4.15 this afternoon

does it have climate control? interested in the light sockets out of it if it does. or the whole unit if need be

as in ur brake pedal or foot pedal for handbrake? did u re-adjust it at the rear rotors when u replaced the rotors? there is an adjuster u need to turn to spread the linings

after a set of climate control light globe sockets/holders. if anyone has a spare climate control lying around they are able to grab them out of. in need of 6. pm me if u have any. can pick up or meet somewhere if better.

received my order of LED T5 globes for dash last night. work really well few darker spots but better then previous cars i have had. also received my front and rear strut braces today. fitted, but need to loosen up rear sway bar i think, went from understeering a fair bit to oversteering now. otherwise still plenty of fun

maybe try putting the copper grease or what ever in between and see how u go. putting the grease just on the pads a lone with out shims have quietened mine down a lot, but still squeals every now and then.

have u got brake shims on the back of all pads? if so have u put copper grease or anything in between the pad and shims?

R33 GTST calipers and rotors fit but u need the bolt spacer put into hub. or u can go R34 GTT calipers nd rotors which bolt straight on. as they are a 14mm bolt like the stagea.

i could possibly get one done at work. if u want to book it in. but would probably take it somewhere more a long the lines of tyrepower, wheelworx. as we dont have the specs for the stagea, but i would be able to do the research and organise something i am sure

i used standard R34 GTT lines all round. but better to get braided front. rears are fine to bolt up. as for BMC its the Same as the R33/R34 cusco do one for the Stagea. there is a picture in the mod thread on here.

spotted yellow stagea turning of portrush rd onto magill rd around 11.30-12 last night. possibly had DAYZ decal on side of gaurd. but dont know

the M35 might have the OBD connection already. but the C34 i know need the consult cable to enable it to plug into the OBD connector that comes with the camp 2 nd most other diagnostic tools. as the consult plug is not the same. OBD is 16 pin. not sure about the early nissan ones. haven't counted

looking for one with a screen. but yea wat ever people can let me know about. as looking for a mfd instead of running multiple gauges around the place

ok kool. thanks for the info. i know of the Ark MFD II as well. but haven't heard back from them. got to try nd find places in adelaide that do them. or any similar. nd then get prices.

wat does it read on yours?

going with a nistune ecu now. so will need to work along side that. do u know how hard it is to wire up? or is it consult cable like others?

does anyone know of any MFD's that show water temp, oil temp, oil pressure, boost. or any others that work with the Stagea? other then a GTR one? will be good if it shows gauges. or bar graphs. or if there is anything else that will work that is not too expensive.

white m35 north east rd around 7 tonight i think it was

plug nd play. autobarn blue vision. but any HB3 will work. just a matter of how white u want the light as too how high of K rating u get. if u want to see mine car catch up somewhere in hills on the weekend at night or something.

i got 4000k high beams nd they are blue nd bright enough, u wont need to go HID high beams

high beams are HB3

Will try come out for meet if I can convince my dad to come out. As have kids nd still court ordered supervised visits at that point one of last weekends. So will see how I go.

new addition as of 10am today. thanks to shelly nd steven for it http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/424774_308508409207105_100001438467673_883777_2134035831_n.jpg

got nistune board put in tonight running stock tune for now. hopefully get it tuned when i get some more parts installed.