Jump to content
SAU Community

Recommended Posts

Hi Guys,

I recently finished a full rebuild on my Gtr R33 and during the process i installed a low temp nismo thermostat 64deg (std 72deg) and greddy radiator 48mm and am about to fit a 19 row oil cooler with relocator and thermostat 72deg Apexi, but i have found that my old 82 deg normal operating temp has drop remarkable to around 68deg with out the oil cooler fitted yet. I oil temp still seems to rise over 70 degs while the water stay in the high 60's. Even with a/c on cruising in mid 30's heat the water temp never exceed 72degs.

My question to you guys is this how cool is to cool oil and water temps. I'm currently not concern at the moment as oil temp is still quiet similar to before it's just water temp low but when the oil cooler goes on i dont want it running to cool and out of the working range of the oil. The reason for these changes are in track conditions oil temps can race sky would quiet quickly and i would the car to handle track work better and manage heat issues. I should also mention i am also running a 8.5 to 9 litre custom sump.

pete

Link to comment
https://www.sau.com.au/forums/topic/101201-rb26-operating-temps/
Share on other sites

Hi Pete,

I have a 48mm PWR radiator with a Nismo Thermostate & a N1 Water Pump. The cooler you have it the better unless its that cold that your ECU tries to richen it up which I doubt. The only thing I found is that the heater might not work as good during a cold night but thats about it. On the oil temp side, well as long as its in its operating temp range you won't have a problem. Its a good idea to have an oil temp thermostate to regulate that, you might have one already.

BTW I have a 9L custom sump with a HKS Oil Cooler that has a built in thermostate.

Hi Pete,

I have a 48mm PWR radiator with a Nismo Thermostate & a N1 Water Pump. The cooler you have it the better unless its that cold that your ECU tries to richen it up which I doubt. The only thing I found is that the heater might not work as good during a cold night but thats about it. On the oil temp side, well as long as its in its operating temp range you won't have a problem. Its a good idea to have an oil temp thermostate to regulate that, you might have one already.

BTW I have a 9L custom sump with a HKS Oil Cooler that has a built in thermostate.

yeah the oil cooler system has a 72 deg thermostat (apexi unit) which has not been fitted yet.

Does anyone know the std operating temp most oils work best with in?

eg(60-120deg?)

pete

Oil temperature, courtesy of Castrol......

In order for motor oil to perform its major function - lubrication - its viscosity (the measure of its thickness or resistance to flow) must be capable of holding up under your engine's extreme temperature conditions. Oil thins when heated and thickens when cooled. Choosing the proper viscosity grade for the ambient temperature of your geographic location becomes vitally important.

A monograde is an oil whose viscosity is defined at only one temperature, either high or low. A multigrade must meet both high and low temperature viscosity requirements simultaneously. This makes multigrades an easy and popular year-round choice for drivers who experience hot summers and harsh winters. They are easily recognized by the dual viscosity designation (i.e. 10W-30 where the 10W is the low temperature, or winter designation and the 30 is the high temperature designation). It is the viscosity modifier additive that produces a thickening effect at high temperatures but is dormant at low temperatures.

-------------------------------------------------------------------------

I have never ever had a Castrol technician advise me that the oil temperature is too low in one of our engines. So we don't run oil thermostats, never have.

Water temperature There used to be a general rule that engines produce their maximum power with water temp around around 85 degrees. Run an engine at 95 degrees and 75 degrees and (without changing anything) it will produce more power at 85 degrees. Due to ideal vapourisation of fuel, metallurgy of components, combustion temperature etc.

More recently it has been found that lower temperatures (than 85 degrees) can in fact produce more power. The idea is, the resulting lower cylinder head temperatures allow more ignition advance (and/or compression) to be applied before detonation sets in. The advanced ignition produces more power than is lost by the lower combustion temperature.

This requires closer to the edge tuning than most road cars would tolerate, they have to survive in 45 degree heat, with the air con on, dawdling along in the traffic etc. In a race car this is not really an issue, so we can tune much tighter.

Having a 72 degree thermostat simplistically means that the thermostat opens fully at 72 degrees. If the cooling system is sufficiently large enough this means that the engine should never get over 72 degrees. If the engine does get over 72 degrees then having a 72 degree thermostat is pretty much a waste of time. Well, it is, until you get a cooling system that IS capable of keeping the temperature at 72 degrees.

Since it gets over 72 degrees, it isn't advisable to tune it (with ignition advance) for more power to take advantage of this lower temperature. Unless you have water temp compensation mapping that starts at 72 degrees.

Hope that was of some help

:P cheers :D

Edited by Sydneykid
Since it gets over 72 degrees, it isn't advisable to tune it (with ignition advance) for more power to take advantage of this lower temperature. Unless you have water temp compensation mapping that starts at 72 degrees.

thanks gary :unsure:

but i actual said it has Never gone or 72deg even on a really hot day with a/c on the works, so i guess that means like you stated the cooling system is now up to the upgrade for general surpose driving will have to see how it fairs on the track.

(so posible i might be able to tune it quiet hard)

Gary what oil temp would you consider safe to run and engine hard on 60deg up wards?

pete

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...