Jump to content
SAU Community

Recommended Posts

Hi Guys,

I had my R33 serviced the other day and was advised my shocks need replacing.

Rear shock is leaking oil. My skyline is a everyday car and I wanted to replace them with standard shocks. I just have a few questions.

* What’s a good brand to get?

* Can i install them myself? or i need clams and better off giving it to the mechanic to do because a few things can go wrong?

* Will the height of the car drop if I change my shocks?

Any feed back would be great!!!!

Cheers :)

Babylon

Hi Guys,

I had my R33 serviced the other day and was advised my shocks need replacing.

Rear shock is leaking oil. My skyline is a everyday car and I wanted to replace them with standard shocks. I just have a few questions.

* What’s a good brand to get?

* Can i install them myself? or i need clams and better off giving it to the mechanic to do because a few things can go wrong?

* Will the height of the car drop if I change my shocks?

Any feed back would be great!!!!

Cheers  :D

Babylon

There is a Group Buy open at the moment, I think it answer most of your questions. The link follows;

http://www.skylinesaustralia.com/forums/in...showtopic=85467

If you have any further questions, please just PM me or post it up here if you want.

:) cheers :

Depending on the cost, I'd look at a better aftermarket shock instead. Aftermarket doesn't necessarily have to mean insanely stiff.

You could source a set of Koni Red non-adjustable sports shocks, and if you can afford it maybe a set of comfort shocks (like Eibach progressive rate springs) to go with them.

If you have a look at the Euro cars, most of them are set up to handle quite well without a back breaking ride. It's not going to challenge a Jap coilover equipped car on the track, but I'm quite fond of the regular BMW 3 Series' suspension setup for street use. It goes where you point it approximately when you point it, unlike your average Camry / Magna / Falcodore, but it absorbs bumps almost as well as they do.

coolies

im thinking of getting pedders

if i replace the rear shocks will i have to replace the fronts?

and would i also have to replace the springs as well?

Sydney Kid - i read that forum i cant make out how much it is for a set of those shocks just for the rear?

Edited by Babylon
1. Sydney Kid - i read that forum i cant make out how much it is for a set of those shocks just for the rear?

1. Bilsteins are $486 for the pair delivered as per the Group Buy. Front and rear are the same price, so $972 for all 4 delivered.

2. im thinking of getting pedders

2. Ouch, not a good idea, cheap and nasty (very nasty).

3. if i replace the rear shocks will i have to replace the fronts?

4. and would i also have to replace the springs as well?

3. Nope, but it would be a good idea to maintain the balance. Old, worn, standard shocks are not really comparable to aftermarket, brand new, sports shocks.

4. Definitely not, the Bilsteins will work very well with the standard springs. You can even lower it a bit using the extra circlip groves.

;) cheers :P

is there any workshops in western subs to install those shocks?

Recommended fitters are in the Group Buy thread.

Heasmans Sydenham NSW

East Coat Suspension Kirrawee NSW

St George Steering Punchbowl NSW

Centeline Thomastown Vic

Traction Tyre & Suspension Rowville Vic

Discount Tyres Service Belconnen Act

:P Cheers:)

  • 2 weeks later...

what do the pedders ones cost

you can get fixed Koni ones for about $200 each or adjustable like me for about $300 each. mine is an everyday driver and i have tham set to full stiffness and you do get used to them. or just have them soft for day to day and stiff if you wana hit the track or just go out for a cain

what do the pedders ones cost

you can get fixed Koni ones for about $200 each or adjustable like me for about $300 each. mine is an everyday driver and i have tham set to full stiffness and you do get used to them. or just have them soft for day to day and stiff if you wana hit the track or just go out for a cain

i ended up gettting some a pair of standard shocks

some jap brand forgotten the brand name

i think it starts with J

$215 for the pair

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...