Jump to content
SAU Community

Recommended Posts

Hey people,

I have a set of 19 x 8 inch (offset+35) Lenso s7 modify rims for sale. these are in fantastic condition. They have been on the car around 4 months and have travelled only 2000kms. So basically brand new. They also come with 23/35/19 tyres that have around 90% tread on them.

These rims have two sets of patterns in the 5 X 114 and 5x 100. So will bolt on to any Silvia S13, S14, S15, Skyline R32, R33, R34, Supra etc (anything 5 x 114), or any 5 stud honda such as newer preludes, intergras civics etc. Also due to the twin stud pattern 4 x 114 can also be obtained by getting 1 more hole drilled onto the back of the rim which would cost you around $50.

These pics are of the actual rims

IMG_81431.jpg

34aas3.jpg

fittingnewbar9.jpg

Lenso1.jpg

lenso2.jpg

lenso3.jpg

As you can see the rims have silver spokes with mirror polished lip and center caps. These rims retail in stores for between $3500 and $4000 depending on where you go. They are also not being made anymore and are becoming difficult to find.

I am asking $2000ono for the rims and tyres (rims in new condtion, tyres at 90% tread)

or

$1600ono for the rims without tyres (rims in new condtion)

I am located in SA

Feel free to post here or PM me if you have any questions

Sean

Edited by mxtcy
Link to comment
https://www.sau.com.au/forums/topic/107524-19-inch-lenso-s7-modify-rims-tyres/
Share on other sites

Selling as i am returning the car to stock.

The tyres are actually really good, never had any problems with them at all. Good in the dry, wet etc :/ Obviously not as good as a $500 a pop tyre, but still a very solid good tyre

Edited by mxtcy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...