Jump to content
SAU Community

Recommended Posts

Im getting 4 new K104's put onto my Stagea this weekend, $800 all up fitted balanced etc, for 235/45/17's onto my new R34 GTT rims - Im in SA by the way.

How long (ie kms) would a set last for? My Stagea isnt a daily driver, and when driven is usually in high density areas..... ie city driving. The Stagea is a heavy car, around 1900kgs with me driving it and fully fuelled - so how much PSI should be in each tyre?

For such a heavy car the K104's are the wrong load rating.

U will need the K107's. Check with the tyre shop who is supplying them.

For such a heavy car the K104's are the wrong load rating.

U will need the K107's. Check with the tyre shop who is supplying them.

Oh? ok, I think the car is around 1650kgs standard. And I know that a Stagea driver in Melbourne is using these hankook 104 tyres on R34gtt rims at the moment and says they are fairly good.

Plus the 104's are load rating 97Y I believe, whereas the basic tyres on my car atm are 92Y load rating, and it was given a road worthy certificate (in Qld when I bought the car) based on these current Nankang tyres.

The K107's are 94Y rating... so what is best? low Y or high Y rating? from what I understand the higher the Y the bigger the load capacity per tyre, see http://www.michelin.com.au/tyres/tyreBasics_speedRating.asp

At the end of the day the Stagea weighs in similar to a VS wagon, or a Magna wagon, so Im sure the 97 rating is aok. Plus from what Ive read they are worth the cash, so Im getting them anyways (plus my budget is a max of $200 per tyre, for 'performance' tyres).

So..... what PSI should I have in the tyre?

Cheers for your information - Brendan

Edited by Tangles

I'd put them on.

I love them. I have travelled a lot of ks on my K104s.

They grip very well.

Tangles, you wont be dissappointed.

Especially considering the price.

If you are putting on 235 17s, let me know.

I'll get you a decent price over here in Mitcham.

BASS OUT

Cheers fellas (by the way Im in Adelaide, so Im not sure our Mitchem here near Unley is the place you mean Bass Junky).

http://www.hankooktyre.com.au/v2/products/...ch=uhpt&id=1088

K104's for 235/45/17 stated as 97Y

I already bargained the shop down a little in price; Im happy (sort-of) to fork out $800 for my first set of 17's provided they look phat on my porky-wagon, perform very well, good value for money, and last me a long time - I drive less than 8000kms per year.

The tread pattern seems fairly aggressive to me, and they have had good reviews here on SAU........... but it comes down to psi also at the end of the day, so that they perform and last well. I will slowly be adding SK's suspension parts over time, although I wont be lowering the car via springs/shocks. At this stage adding swaybars & castor, and will add subframe alignment kit & camber when I can afford to.

Cheers, Brendan

Edited by Tangles
about $185 each....

Good pricing.......

I probably could have rung around more places and got them slowly down a bit, but how far do you go?!

Im sure they will be worth every dollar..... I hope. Im thinking start off with 36psi in each tyre and see how they wear and handle.

Never had 17inch mags before, cant wait to see how the GTT rims & 235wide K104 tyres look on the swett-as Stagea RB25det-smokin station wagon. :happy:

Cheers to you all, go the Crows.

Brendan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...