Jump to content
SAU Community

SUNDAY 2nd MARCH **HARRY's 4 PIES MEET**


Recommended Posts

  • Replies 110
  • Created
  • Last Reply

Top Posters In This Topic

Nah stuff the hotdog....

Stick to the Chicken pie, with Mash and Gravy with abit of tomato sauce.... Hmmmmmmmmmmmmmm

U should have came with us afterwards, there was heaps more

FAT cars later on......

You should make this a regular Sunday outing man....

Originally posted by d.3.v.i.l

Nah stuff the hotdog....

Stick to the Chicken pie, with Mash and Gravy with abit of tomato sauce.... Hmmmmmmmmmmmmmm

U should have came with us afterwards, there was heaps more

FAT cars later on......

You should make this a regular Sunday outing man....

i'm in for that!!! i dont have uni till about 4-6pm on mondays anyway :P

Originally posted by [ryan]

lol

that's the same ranger who ALWAYS comes over when there's a meet. The other Holden-loving bogan ranger didn't make an appearance though, i was surprised

You could hear on the ranger's walkie talkie, "My BOV is bigger than your BOV". BAHBAHBAHBAHAHAHAH

Sounds like you all had fun, pity I couldn't cruise on but I'd have become a road toll statistic with so little sleep. Kicked myself all the way home!

That GTR ripped. one of the quickest cars I've ever been in! Would have liked him to really open it up but it wasn't the place to do it and believe me that car had soooo much more to give!

Good to see new people too, the more he merrier!

Sorry to all who i didn't say hi too.. Was a bit edgy so tried to

stay away from people...

To get to Harrys.. On george st after the cinema's turn right.

goto the end

turn left.. then turn right straight away.. go down the hill.. (*)

i think after two sets of lights there will be a farrarri store to you

left.. Its on the corner.. You have to turn there.. go all the way

down to the end.. turn right.. and your there..

or you could continue from (*)

head down towards the coke a cola sign, turn left and drive

through the cross.. go all the way to the end.. and turn left

drive down about 500 metres and your there.




  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...