Jump to content
SAU Community

Recommended Posts

original gtr front bar??

patto1234: do u need the reinforcement bar to fit the gtr front bar onto a gtst? if not how much u chipping in for the package?

I was looking at this bar a few weeks back and I do believe it's genuine GTR. Blukie can clarify that. You don't need the reinforcment bar to fit the FB, basically there are number of factory mounts on the Gtst (under the indicators and under the wheel arches) that you can screw the bar onto. I did this recently...and it was quite secure. Fits like a glove. In regards to how much I would chip in, I have spoken to Blukie and he was after $100 for the reinforcement bar. So I guess thats how much I'll chip in. Spose it's not really much but thought it might be able to help a potential buyer out. Let me know if you're still interested

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I'm interested in the

32 GTR Guards Gunmetal good condition no dents or scratches $300 Each

Are you prepared to post?

Sarumatix,

If U wish I can post (at your expense). I have just double checked and there is a blemish on 1 guard where the clear has peeled off the guard. It's round like 4 cm in diameter. If U wish I can take a close up pic of the blemish and PM to you. No scratches or dents though.

I don't want to pull the splitter off incase I chip the paint on the bonnet.

Sorry Skyquest, I'm waiting for someone to PM be back about wanting piping from bothsides. I will let u know as soon as he's PM'd me back. He's paying $75.00 each side.

hey Blukie

jut wondering if you've sold the rear end yet?

thanks

Macca

Hey Macca,

sorry I just sold the rear end. Just waiting for the guy to pick it up. If it falls through I'll let U know.

Edited by blukie
yer mate, not worried if it doesnt come with them but interested, price for both??

Hey, you can have both doors complete with trims and mirrors for $575.00. Door skins are in excellent condition.

how much for the rear seat and would you post to VIC?

FWIW, if you remove the splitter from the bonnet it will stuff it. It is soft and will be shagged by the time have it off. The only option is to buy one from nissan as i did.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...