Jump to content
SAU Community

New Fmic Means No Pod And Now Airbox

Saliba
 Share

Recommended Posts

Saliba Contributor

Saliba

Posted
Posted

Hi Guys,

Recently upgraded to a Apexi FMIC which means i now need to remove my pod for my car to be semi legal ;p

in regards to putting an airbox back on can i use one of those carbon / fibreglass boxes which are called cold air boxes?

im trying to find out what the best possible thing i could do, ive heard that the stock airbox will be better for the car as the car would be breathing from the cooler and not the pod / airbox thus creating better airflow....please tell me if that is a false statement.

Any help would be greatly appreciated as im new to the world of modifications and loving learning as much as i can.

Thanks

Husky33 Veteran

Husky33

Posted
Posted
Hi Guys,

Recently upgraded to a Apexi FMIC which means i now need to remove my pod for my car to be semi legal ;p

in regards to putting an airbox back on can i use one of those carbon / fibreglass boxes which are called cold air boxes?

im trying to find out what the best possible thing i could do, ive heard that the stock airbox will be better for the car as the car would be breathing from the cooler and not the pod / airbox thus creating better airflow....please tell me if that is a false statement.

Any help would be greatly appreciated as im new to the world of modifications and loving learning as much as i can.

Thanks

ok, if you're in VIC you can only have 1 intake modification, which it seems you know anyway. However, having a cold air box around a pod is still an intake modification. Therefore either that or the fmic will have to be removed. The only way you can legally have an fmic is to have a stock airbox installed...period. I would personally put a good panel filter into your stock airbox. Trust me it will still go very well, maybe a little down in top end and "whoosh" sound..lol, but not really that bad. Think of it this way: An fmic will outweigh any negatives of putting a stock airbox on.

_8OO5TED_ Mentor

_8OO5TED_

Posted
Posted

damn you guys over east get taken hard! 1 intake mod??

Oh well, it seems an aftermarket panel filter works very well compared to a pod anyway so your performance loss would be very minimal, if anything id say.

Husky33 Veteran

Husky33

Posted
Posted

Yeah but the whole issue in VIc is not whether the pod is boxed or not, it's the EPA restricting intake modifications to one only. Whether it's boxed or not, if it's not stock and you have a fmic dont whinge when you get epa'd.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • hardsteppa
      Hi everyone.

      By hardsteppa · Posted

      Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...