Jump to content
SAU Community

Recommended Posts

Hey Guys,

Wanting to sell my car,

This car isn't my daily driver, only driven roughly a few months a year

There are a few item's there that haven't been fitted,

I Just don't have the time to fit them, but all come with car.

Last time car was Dyno'd it had 180RWKW, However I didn't

recieve a Print Out, I will try and go back for another run and get a

print out.

Car has just under 12 Months Rego

Can swap for Cheap AE86 or R32(Turbo) with cash adjustment!

SOLD! Deposit Taken

Car Has roughly 95,xxx Km's

Has all the Usual Power Options, and a 3 Point Alarm!

Engine/Performace

Alluminium OverFlow

Apexi N1 Muffler

APEXI Air Intake Kit

HKS SSQV BOV (Not Fitted)

Brass Button Clutch

Dump Pipe (Liverpool Exhaust)

Full 3" Exhaust

Greddy Turbo Timer

Hi-Flow 25G (Unsure Of Spec's, But have reciept from GCG)

Hybrid Intercooler (Genuine)

Oil Catch Can (JustJap)

TuneAgent Turbo Manifold

TurboTech Manual Boost Controller

Wallbro 500hp Fuel Pump

Oil Cooler With Motorsport Fittings (Not Fitted)

Stereo/ICE/Audio

MB Quarts Splits 6.5"

Relocated Battery (Optima Yellow Top)

Rockford 12" Subwoofer

Kenwood MP3 Headunit

Alpine 4 Channel Amp

Styling/Interior/Exterior

Apexi Boost Guage (EL)

Gear Knob

C's Short Shifter

Full Respray in 3 Layer White Pearl

RailWorks Body Kit

Leather Gear Cover

Momo Steering Wheel (Genuine)

Trust Guage Pillar Pod (Not Fitted)

Wheels/Suspension/Brakes

Adjustable Castor

Front and Rear Slotted Rotors

Front and Rear Strut Braces

Street Spec G4 Coilovers

Lenzo 18" Wheels

Nankang Tyres (Rears on Wear Indicators)

I Will try and take some better pictures when the weather clears up.

EngineBay.jpg

SIMG0014.jpg

SIMG0002.jpg

SideBehind2.jpg

Side2.jpg

RightFront2.jpg

LeftFront2.jpg

SideFront2.jpg

BehindSmall.jpg

The Momo Wheel and Boost Guage are no longer those item's in the picture.

Cheers

Josh

Edited by GreddyGo

Thanks buddy,

But i'm after a really dead stock R32,

Pitty your in melbourne, don't have the time atm to go interstate!

Will definately keep you in mind!

Cheers

Josh

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...