Jump to content
SAU Community

Recommended Posts

Howdy all.

I'm selling my R33 to concentrate on business and paying off my house. And then I will shoot for something more expensive like a R34 or R33gtr. I have a company car and the skyline is a hobby and weekend driver.

The short of it:-

The car is an 1993 R33 GTST.

It has 185KW in none shootout mode at the rears. (200-210kw in shootout)

86xxxkm on the clock.

Wine Red.

Im after $16500ono.

SOLD!!!

The long if you want to read:-

New HD exceedy clutch, less than 10k ago, did rear seal at the time as well. Radiator serviced

Timing belt done along with, Water pump, Idler and tensioner bearings, Front seal

Tested compression – 150psi - even all round - this is good!

JVC Kameleon stereo.

Bell mouth 3" dump and front with exhaust wrap, 3" satinless catback exhaust

2 point imobilizer with remote and central locking

Jaycar IEBC (Independant electronic boost controller)

Jaycar DFA (digital fuel adjuster - like apexi SAFC) Tune by Matt Spry-225hp, but his dyno is 10% pesimistic. pic attached

Walbro 255lph fuel pump

Copper plugs gapped to .8mm

Coilpacks are good - there is no misfire at all.

Leather gearbox boot and handbrake boot

K & N air filter under a ABS plastic partition - secured well.[/size] GBF adjustable BOV

Big front mount intercooler that uses original intercooler holes, with custom polished stainless piping.

Serviced every 5k

9" wide 17" work expec rims on the front

10" wide 17" work expec rims on the back

type M side skirts

Aftermarket front apron - not such which brand.

I do have the rear pods (repaired), they need painting and fitting.

All in all, the car has very good paint and body work. This is why I bought it.

Kenwood dual mags in the front doors.

[/size]

Pics attached.

I will need to roadworthy it.

Inspections welcome. Please PM me, or call on 0427762040

Test drives to those who show genuine interest and come with check or cash in hand. (Just incase you crash it!!) I recon if you drive it, you will want to buy it.

I think that's all, If there anything I've missed, please let me know.

Chris

post-19015-1150089529.jpg

post-19015-1150089609.jpg

post-19015-1150089636.jpg

post-19015-1150089790.jpg

Edited by chrissso
Link to comment
https://www.sau.com.au/forums/topic/121924-r33-gts25t-for-sale/
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...