Jump to content
SAU Community

Recommended Posts

low down is, i got car serviced on fri morn, it seemed perfectly fine, with the report saying all it needed now was a front end allignment etc...

got home from drive ins last night, put car into PARK tunred stereo off, and i could hear a fairly loudish whistling/whining noise from under the hood..as soon as i turned her off it stopped, but turned her back on and it came back again after about 5 secs..(the temp gause is always norm, i am sure of this cause i am paranoid about temp from a previous bad experince)

just took her for a burn around the block a few times at norm temp, and came back no noise at all apart from nomral, however when i switch the key off I THINK!! i heard a little slightest squel if you wanna call it but cant be sure

anyone know what this could be please..... i have to drive to adelaide tomorrow morn(moday)

i attach a pic of something that i thought was wierd but not sure if thats the way it should be or not(the little slits/holes between the pipes)

Link to comment
https://www.sau.com.au/forums/topic/12650-urgent-help-needed-please/
Share on other sites

hmmmm i dont know what to do, wether to still go to adelaide or not, either way if i do i think ishould get racv total care so if i do die on the way up there, i can at least get a free tow all the way back home from anywhere in aus, and get a hire car for therest of journey hehehe....this sucks, always something happens either when you have to rely on the car or you have had a good night(ie the meet) then get home and something like this freaks you out)

it sounds like the belts, check the tightness if the belts if they are hard as a rock or loose when pushing them down, thats your problem and you'll need take it back to where you did the service and loosen them or tighten them accordingly.

yep i had a similiar problem on my silvia and it turned out to be power steering pump, it was hard to figure out what it was too!

My mechanic told me that if i drove it too long like that the pump might seize or something and damage other parts ending up in a big bill$$$...

So check your steering pump, if its not that then maybe waterpump?

A couple of possabilitys here:

1. Does it sound like Air squealing out? (rubber hose?) vacum type sound?

2. Or more of a rubber on metal sqealch?

if it sounds like no 1;

Check all your intake rubbers & seals, make sure all clips are tight. (keep in mind that this leak might not be noticable, but under presure or vacume it might open, a split or pinhole in a rubber seal somewere, or even pipping .)

After you have checked everything under the hood, it might pay to take your front bar off and check your intcooler and intercooler piping. If you car is running higher than factory boost, it could be possable that there is a slight "stress" fracture in your cooler or some of the pipping. basicly check everything air travells through.

If it sounds like number 2;

Go down to repco, or somthing and buy some CRC Belt-Grip and spray it on all your belts (Not too much otherwise it will make a whining/supercharger sound). this will establish weather it is infact a worn belt or, a worn part that the belt runs. eg powersteering, ac etc. if it still makes a whining sound, its then a process of elimination: look for worn components under the bonnet. eg leaky power steering?, is there a way that oil can leak onto a belt? Does it still make the noise with your A/C on & off??

Also it might pay to check your timing belt. ( DONT SPRAY THIS BELT WITH BELT SPRAY!! =)

Good luck & Hope this helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...