Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

car could easily run high 11's.. was running low 12's but that is on some crappy rubber and very shit launches.. only been out there once..

with semi slicks and the right launch, it could easily get into 11's

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2396444
Share on other sites

yeah it is at the wheels.. yeah dyno sheets i will show you.. it was tuned by unigroup so they well i think are the best tuners in sydney, and tuned it safely.. will scan dyno sheet in for you

been holding up perfectly fine for 8 months no hiccups or anything..

the blocks are solid

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2402993
Share on other sites

$200 Spotters fee for whoever refers the car to friends and they go through with the sale.

This is free cash for whoever refers their friends to buy their car.

So go on tell your freinds and get 200 bucks for free if they buy the car

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2414010
Share on other sites

peak of 1.2 bar which is 17 psi. So it normally sits at 1.2 - 1.3 bar to get that much power, with the hi flow turbos they are all not the same, so Unigroup have told me that i have got one which is pulling more punch since they have tuned it safely and reduced the power just in case, but it could easily go to 270rkw they say.

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2414648
Share on other sites

  • 2 weeks later...

Keeper: splitfires does the job so well

and i recapped the plugs it .69 but that is all

splitfire helped so much..

dazz: side skirts came with car when my mate purchased these ages ago, so i assume these come from japan

:)

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2462410
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
×
×
  • Create New...