Jump to content
SAU Community

Recommended Posts

carrillo's just seem a huge step up... i mean there's the 350rwkw and then there's like the carrillo's at 600rwkw... we need to find a 450rwkw rod. 350rwkw is easy to reach with a 3lt block and 450 is a happy medium, high enough power to be very reliable, but not so high that you are spending mega bucks

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

yeah i'm interested in the chevy ones too... i think that carillo rods are a bit beyond what i'm aiming for. I'm going for plenty of low-mid range power rather than all out topend. And once you pass the 320rwkw or so, the gearbox and other parts start to need looking at and i can't afford to do that!

Ah well Im aiming for 450rwkw at arounf 1.0-1.2 bar, If i get power hungry I want to make sure I done need to gringe every time I give the car a boot full, so Carrillos are the way I am going besides at around $1100 + machinng which is around $600 your not far off $2,400 for the carrillos, and if you do ever need to rebuild you can just buy one carrillo not 8!!!

The 2.5, 2.6 and 3.0 rods are all different in length. You will need to decide what capacity you want the 3.0 will make the same power at lower rpm and it will tend to last longer. If you go 3 litre then I assume as you, me and GiHOr33 will want RB30 Carrillos we will get a fair discount

Jordan

Update: Ive was given a hint. I found Oliver rods they said that they would suit a supercharged small block making 1100HP at 8,200 rpm. This is the same cylinder presure as a RB30/31 making 750/800Hp so hence they say these will do they are $125 US a rod which makes a set $1,500 Australian, allot cheaper than Carrillo what i want to know is how good they are, maching to make them suit will cost around $400 i guess so $1900 all up

Sydnekid or anyone else know about these rods and how good they are???

GR8NES/700

Hi GR8NES, what do I know about Oliver...........

* Oliver make good stuff, been around a long time

* used a lot in Nascar

* the rods are "I" beam

* they come standard with ARP rod bolts

* I think it's Trust that sell rebadged Oliver rods (and charge twice as much)

* they make forged and billet rods in three weights, standard, lightweight and super lightweight

* a set of 6 light weight, forged "I" beam, unmachined rods with 7/16 ARP 8740 rod bolts should be around $A1200 plus freight

* for about $A15 per rod extra you can upgrade to the ARP 2000 3/8 rod bolts

* my personal preference is their standard weight, billet, "I" beam, unmachined rod with 7/16 ARP 8740 rod bolts. Used them in a couple of Chevy speedway engines, no problems.

Never used them in a Skyline engine, but no reason why they would not be OK for the job.

Hope that helps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...