Jump to content
SAU Community

Recommended Posts

Have a look in 'group buys' - there was a deal in there for Catco cats recently. Send him a pm and you may still be able to get one for the GB price (around the high 300 dollar mark If I remember correctly)

From what I hear they are very good... Will most likely purchase one myself :laugh:

I swear I told you this in some other thread?? Anyway...stock GTR cats are very good and are 2.5 inch...the really good news is they bolt up and cost under $100

Yes where do i get one

I would look up the yellow pages and find compliance places...Like maybe try SVI they could point you in the right direction probably

Thats to much work, i started uni again and am working i dont have time to go chasing around for second hand parts

ok, so you said your too busy to go looking for parts, but you are asking where you can get one, dude they gave you advice on what to do, take Buntas advice on the GTR cat, it will take u just as much time to make a few phone calls and pick one up as it probally will to get one any other way,

or ask your genie if he knows where you can get one and he might do the running around for u,

I know thats why im asking if anyone know where i can get a good price on any 2.5 inch high flow cat.

Dont be so lazy! Even if someone tells you exactly where to go you should still ring around a bit and make sure that you are infact getting a good price! Research prevents you getting ripped off

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...