Jump to content
SAU Community

Recommended Posts

that's right,

r31 skyline

rb30de with blown head gasket

crap interior (STD)

phat drift rims (stockers actually)

mad stereo (non at all but don't tell anyone- oh crap sorry there is a set of speakers)

spare tyre that's been smoked off

old craper that needs an owner pls come and take it away!

$200 for the first person in Bris to ring this sunday will own it

its white

unrego'd but could be

done low k's 450,000ish

setup for drift (stock as a rock)

ITS A PIECE OF TURD REALLY!!! But I hate it sitting on the road infront of my house

Pls Buy IT

Contact

Andy

IN BRISBANE

[email protected]

FIRST TO SEE WILL CRY... um BUY

Edited by madr32
Link to comment
https://www.sau.com.au/forums/topic/130846-r31-skyline-for-sale/
Share on other sites

looks like a great track car setup, nice spoungy suspension with lots of body roll Perfect

the car looks like its in reasonable condition from the outside and intirior

is fair ill let you know if i can come up with the cash by sunday

thanks for the pics mate

Dynoed at Bullcrap Dyno's in Brisbane

Tuned by "Tuned Automotive" and the engine blew!!! (there's a good place to take you're car if you want it DESTROYED- Ba(*&^(*& , s(*& absolute wankers

got upwards of 80awkw (oh that's right its a rear wheel drive!!!)

totally stock engine actually

I've decided to take $190- for the car, my heart is breaking at the moment

I'll throw in a pair of safety glasses and a spare tyre

I'll throw in a set cover and a stereo speaker

I'm desperate to sell this wonderful specifimen of turd

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...