Jump to content
SAU Community

Recommended Posts

Hey Guys,

I have just sent my car to the mechanic and he will be looking at it 2moro but i would be interested to see what you thought of the issue i am currently having.

Basically the car runs fine day to day and the only issue i have is that when the car is pushed it starts to rev fine, but then around the 3500 - 4000rpm mark its struggles to rev and feels unwilling to rev (almost like petrol is not gettin through properlly) and then towards 5500 - 6000 it seems ok again. But my friend and i drove it the other nite and he could tell straight away (also a 32 owner) and im starting to worry.

It has been this way for a while but because i dont rev beyond 3500 too often i didnt pay much attention..

So yeah, any ffedback appreciated

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/
Share on other sites

Oh ok, i was thinking it would not be a major problem as in general the car is fine and the problem is only under hard driving in that specific rev range as i said. My main concern that it was not major as in like a few cylinder loosing compression and a possible critical problem in the block. But i guess i just wanted assurance...

cause wen i want to drive faster now i generally drive to 3500 which its fine to and then change, but in first gear off the lights its more likely to rev clean right through to 6500rpm and the problem happens more in 2nd, 3rd, 4th

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/#findComment-2435222
Share on other sites

Oh ok, i was thinking it would not be a major problem as in general the car is fine and the problem is only under hard driving in that specific rev range as i said. My main concern that it was not major as in like a few cylinder loosing compression and a possible critical problem in the block. But i guess i just wanted assurance...

cause wen i want to drive faster now i generally drive to 3500 which its fine to and then change, but in first gear off the lights its more likely to rev clean right through to 6500rpm and the problem happens more in 2nd, 3rd, 4th

I had the same problem with my r32 gtst. To fix it I made put the timing forward, the tiniest bit. and the problem was gone.

I checked all my coils and plugs and they were fine so this was a last resort.

It worked. *shrug* dont ask me why.

hope this helps

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/#findComment-2435242
Share on other sites

I think there ia a tutorial, mabey sticky about the coilpacks cracking due to heat, check it out :ninja:

Here tis'

http://www.skylinesaustralia.com/forums/in...showtopic=32356

Hrrmm after reading this im not sure this would be my issue, ad the car only has a 3" cat back and pod filter...otherwise stock and has been all its life, i bought it in original nick with not a thing touched, and its never been boosted which seems to cause the problem with the coil packs due to the increased temp

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/#findComment-2435257
Share on other sites

I had the same problem with my r32 gtst. To fix it I made put the timing forward, the tiniest bit. and the problem was gone.

I checked all my coils and plugs and they were fine so this was a last resort.

It worked. *shrug* dont ask me why.

hope this helps

Actually its interesting you say that, because my mate when i got the car helped me do first service and was suprised at the position of the timing as he used to hav a 32 and knew a bit bout them and did a lot of work on his car. Ill mention it to mechanic..

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/#findComment-2435264
Share on other sites

Also I have noticed when the car is just started (cold) and then driving it is more noticeable, it just seems really unwilling to rev, its like ur asking to much and the fuel is just sputtering in as u build up some revs so i dont push it, but i know when i tested it (a year ago when buying) we cold started and it was more than happy to rev hard and it pulled hard and quick, i dont know what spark plugs the mechanic put in it last time also he didnt use synthetic oil (which he will this time after i asked him to) but i doubt thats related

Link to comment
https://www.sau.com.au/forums/topic/131546-engine-issue/#findComment-2435282
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...