Jump to content
SAU Community

F/s (tas): Rb30det!

VHR32
 Share

Recommended Posts

VHR32 Community Regular

VHR32

Posted
Posted (edited)

R32 Nissan Skyline RB25DE cylinder head

Series 2 RB30E short motor

These heads are hard to get and will bolt straight on to the RB30 block, no variable cam timing to worry about. It will have 8.3:1 compression ratio and will flow alot more air than a RB30 head. Ideal for turbo conversion!

The engine apparently was in good condition before the head cracked on it. It has all the oil and water connections to suit a turbo.

Fit a Garrett GT3588 and you will have 300rwkw!! (with appropriate fuel system etc)

$900 lot.

PM or phone 0407 842 553

Payment by cash on pick up or direct deposit and will send when clears.

Located in Launceston TAS 7249, freight to anywhere arranged no problem.

RB25head.jpg

RB30.jpg

Edited by VHR32
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Updating results.  Using ATR45SS-0 model VS UHF57-900. Those two are very different turbos, different wheels sets with different wheel hub profiles but yet with almost identical result. I’m intrigued with both turbos performance. ATR45SS-0 was a 61mm turbo first developed in May 2020, UHF57-900 was a 62mm turbo developed in March 2024 as a powered up alternative of a G30-900. On paper ATR45SS-0 maxed at 563rwkws, while UHF57-900 maxed at 568rwkws. ATR45SS was slightly more responsive with slightly better power band through the mid range.  Road driving ability, ATR45SS-0 had better throttle response, felt more robust under throttle, as it wakes up earlier. I think G series wheel hub design made it to have higher inertia under light throttle. Doing bit more prototype work in the next few weeks, will update result when its back on dyno again. ATR45SS0 Blue, UHF57-900 Red Chequered tuner's Dynapack hub dyno, E85 fuel. Mod list is in video below video_20240604_114214.mp4    
    • kevboost7
      Wastegate Boost Reference For Twin Turbo Rb26 Using Dual Port Gates

      By kevboost7 · Posted

      Did you run the power cables for the mac valve to the other side of the car near the fusebox? Utilizing the stock boost controller cables? or did you run new ones?
    • JeffWithaJ
      Stupid HICAS Question?

      By JeffWithaJ · Posted

      Hey I have a potentially stupid HICAS question 🤣 I'm currently doing a full hicas delete, Power steering pump modified to non hicas, all lines removed from the car along with all electronics. My stupid question is - Do I need a lock out bar? is there any reason why I cant just remove everything from the rear end? I already have a lock out bar but thinking to save a few extra grams I could also get rid of the arms and tie rods as well and just run it with nothing in its place? or would it have a negative effect on handling?
    • stasis
      Arm ball joint

      By stasis · Posted

      Hi how are you guys?  I know i have been absent for years but im coming back slowly guys just wondering if anyone know where the ball joint on the NISMO arm front and rear can be replaced with OE parts?  Also  i know this is not the thread looking for springs and blistein shocks for the 260rs. Please advcie     cheers    yudy
    • stasis
      Group Buy Braided Brake Lines Hel.

      By stasis · Posted

      Hi i do you have for stages 260rs?
×
×
  • Create New...