Jump to content
SAU Community

Recommended Posts

post-11094-1159706016.jpgpost-11094-1159704951.jpgpost-11094-1159705828.jpgpost-11094-1159704923.jpgpost-11094-1159704889.jpgSelling my beloved Series 1, it's had a few mods done. Project that never really got finished, so the car doesn't need much to get it really going hard

Nissan Skyline R33 GTST

Manual

Hi-Flowed Turbo by JPC in Thomastown

Lowered on RSR springs all round

102,000 kms

Excedy Heavy duty clutch

3" turbo back exhaust with HKS muffler

600x300x75 FMIC

19 inch rims with 70-80% tread

Pager Alarm with immoboliser

K&N pod filter in stainless steel cold air box

Strut brace for rear

Service done every 5,000 kms

Pivot turbo timer, looks very standard

Sound system including DVD player and screen

Electronic rust protecter wired into car

Extra parts to go with car:

16 inch rims

Stock exhaust

Fuel cut defender

Greddy Profec A

many more

Can't really think of anything else, just need it to be sold.

This car is my passion but as most of us would know i'm in for some interesting times.

Asking for $16990 ONO

Pm me or call me on 0402428854, P.S. i don't really like private numbers

i'm in melbourne

Edited by improvin
Link to comment
https://www.sau.com.au/forums/topic/136923-14500-cheap-with-modsselling-asap/
Share on other sites

hey sorry guys i can't swap it for another car, fiance already has a normal/friendly car; So its up to me to make the "sacrific" thanks anyway.

Need to really sell it as soon as possible, open to any other reasonable offers...thanks once again.

Guys

This car is the best series 1 R33 I have seen. Subtle mods, yet still manages to grab your attention.

I know Anthony Personally and I have never seen that car with a spec of dust on it. I waited 3 months to sell my skyline and it was immaculate, you just have to wait for the right person to come along.

I assure you guys, the first serious person that goes and has a look at this car will buy it, you CANNOT fault it. He is after a Motorbike and I know that he wouldnt sell it for another car!

After being a owner of a R33, I must say, they have a classic look and bulletproof reliability- this ones had all of your usual Mods done so no more to spend, sometimes we forget that stock ones are going for like 1k cheaper, but you would have to spend 6k+ to just get it to the same level of mods as this one.

Good Luck with the sale man I know itll be sold soon.

Guys thanks heaps for the support!!!! i thought this was pretty cheap for a car with a couple of "not bad" mods......but not any real serious buys though.

I need to sell the car asap serious offers considered.

thanks again guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...