Jump to content
SAU Community

Recommended Posts

Scotty you've gotta give me another ride in the GTR, see how it feels compared to my GTST.

Maybe if your a good little boy :P

when i get my new rotors in i will take ya for a drive, she doesnt stop too good these days :ninja: but that will be soon fixed!!!

Current Spec’s

GTR Front Bar

Vailside Side Skirts

GTR Rear Bumper Fins

Rays Drop Forged Aluminium Rims

Trust Intercooler

Apexi N1 Cat back exhaust

Blitz Pod Filter

Cusco Adjustable Coilovers (Track Spec)

Front Strut Brace

Exedy Heavy Duty Clutch

And lots of stickers!!!!!

Power on these specs was 137.9rwkw

Just added

Re chipped ECU (need to re-Dino for rwkw)

Future mods will be

A boost controller

A Dump pipe

An Aftermarket cat

High flow the standard turbo

Some gages

A Greedy tech Informeter

And some stereo gear

I only want about 180-200 rwkw

Ed say’s with that setup I shouldn’t have a prob getting 220rwkw if I get a bigger fuel pump.

555cc injectors,

Greddy Emanage

Greddy E-01

200kw atw. not much for you 6 cyl boys but itll be very quik for a 200 :(

Its in the shop atm getting kit, sprayed and repaired. god only knows when it will be done as he's takin his sweet goddam time. i met a fella on here who has a white 32 GTR there as well ;)

mind you that prolly wont happen as im going to sell it around my bday and either buy something else or pay out my loan and get a run around and start saving for house and other stuff :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...