Jump to content
SAU Community

Recommended Posts

Hey guys,

Love the car, absolute blast to drive, however now that i've been driving it for a bit, i'm starting to look into its hopefully minor issues.

Issue 1) After full wheel alignment and balance, car still has slight vibration at high speeds - i'm calling shit tyres since the guy at the workshop said the rear's where out of whack and slightly egged just want confirmation.

Issue 2) Car pulls to the left if I let the steering wheel go - car has coilovers but are old and way to hard and i think oversprung, possibilites? castor rods? control arm or something i can adjust?

issue 3) how to tell if car is over sprung - i think it is, had 2 people get in on the passenger side, was sagged and i could 'feel' the damper move and actually work rather than the spring just bounce around like usual - my thinking is with more weight its stopped the spring from moving as much and allowing the damper to do its job. With just me in the car, if i go over a large bump you can hear the springs 'resonate' and clang around.

Issue 1 and 3 i think can be fixed with new tires and a change in suspension, issue 2 i'm not sure about. No obvious viscous fluids so i'm not sure about the castor rods, but my mechanic is away so i can't talk it through with him.

Cheers guys! For once i'm actually looking forward to working on a car!

Link to comment
https://www.sau.com.au/forums/topic/138960-couple-of-handling-questions/
Share on other sites

1. is the vibration through the steering wheel or through the seat?

if its through the seat, more than likely its the rear tyres fault as the guy said

2. cars pull with uneven camber and/or castor. they pull to the side with less camber/castor.

to fix the problem get castor rods/bushes. if the camber is uneven too get camber bushes/arms.

all this information will be on you wheel alignment report. both camber and castor should be very close to even.

if there is castor adjustment, wheel aligners will set the left up with 0.5-1.0deg more castor to accomodate for the natural camber of roads (which allow for water drainage)

Edited by salad

well there's my answer for the pulling to the left, wheel alignment report shows left at +4.41 degrees and right at +5.57 degrees.

Are the castor rods seperate to the bushes or are they together? Just replace both?

Vibration is the last thing ot worry about i guess, it only happs at about 110km/h plus. Before the alignment it was about 80km/h plus

sounds like front tyres still out of balance... alignment wont affect vibration.

rods are seperate to bushes. replace the bushes in the stock rods or replace the whole rod with an aftermarket rosejointed item

bush's are the more street friendly option.

i think you can get enough adjustment out, but im not sure, someone else will have to clarify as i've never had bushes.

rose jointed rods have a lot of adjustment, more than enough, but they're not recommended for street.

rose joints are illegal on the street, because when they wear out they fall apart.. Having your suspension detach in the middle is generally not a good thing :laugh:

You don't need that much adjustment on the street. On the track, sure.. especially with semis :)

If your alignment is fine but the bushes are clapped out just get the bushes replaced. Otherwise get adjustable castor rods and have at it (have seen the noltec ones for a 32 GTR and they make a brick shithouse look like a tent).

Vibration is either caused by out of balance, cheap out-of-round tyres or that your wheels aren't perfectly true on the hubs (you will probably get brake vibration if this is the case because the rotor will be out as well). Edit - if your wheel bearings are on the way out that can cause it too.

If the springs are bouncing around like you say it sounds like the car is oversprung. Personally I think it's foolish to run rock hard suspension on aussie roads, get some nicely matched springs and shocks instead!!

Edited by Kinks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • CTIS (Central Tire Inflation System) has existed since the 80's. I'm looking into buying a Hummer H1 and they generally included it. 
    • My idle is set at 950rpm though - Moving the timing around 20 degrees is not really what I'd call a calm idle. That said... neither is chop, by definition. The LS ECU likes to adjust timing to hold idle as opposed to air. It'd work, but generally speaking there'd be a discrepancy in the base idle and the IACV would want to move the timing around anyway to maintain said idle. I think I'm just going to keep the timing steady anyway. Preserve my engine mounts.  My aircon is now officially regassed. As the guy was reversing I noticed my reverse lights do not operate, along with my reverse cam. This is a bit distressing, because 100% of guides talk about which wire to connect to backup cams as "the goes with the [other color] wire". Often when doing conversions. Unfortunately the R34 colour wires aren't documented Unfortunately I had a T56 Magnum gearbox with it's reverse switch, which also isn't documented. Unfortunately there's definitely not documentation for people with both of these in the one car. Unfortunately I forgot. After many hours of this, I have a reverse cam and reverse lights again. The wire going through the trans tunnel to the reverse switch had broken. Upon inspection, it looks like this one wire had about 7 spade terminals and extensions in it.. for reasons I cannot possibly comprehend. I also spent the 750 hours required to clean up the wiring behind my head unit which now looks like this: This is a monumental improvement relative to what used to be there WRT triple gauges, head unit, traction control, wideband controller, and whatever the f**k OEM stuff still exists there in various states of connectivity/needed. Next step is to check in at the Exhaust shop to see/confirm how much clearance I have, to decide what mid mufflers or 'resonators' (which are just straight through, narrower mufflers) I can add and hopefully cut out a lot of exhaust leaks, pinhole, v-band or otherwise. But first step will be to 'take a look' before the next step.
    • Fark the AFM card and Nistune, Haltech Nexus S3, DBW, cruise control, flex fuel, dis dat.  
    • It's most likely the bolt/bush where the cover bolts back wore and allowed cover to move forward.
    • Still haven't put the injectors and R35 AFM in so we can tune the bloody thing for the HG highflow it got mid last year! I think I can forecast the upgrade path to a bigger twin scroll, external gate, Haltech, flex setup, Samsonas, dis dat, etc will be .... a while away!
×
×
  • Create New...