Jump to content
SAU Community

Recommended Posts

I have a set of Bilstein height adjustable struts ready to go into an R32 GST-T. This suspension gave great handling in my car and a good looking ride height but I have upgraded to some TEINs for a bit more track work.

Price $550.00. Located in Hills area but can organise free delivery in Sydney.

Contact me on 0417 366 888 or [email protected]

post-3910-1162292283.jpg

Edited by 321 GO
Link to comment
https://www.sau.com.au/forums/topic/141271-sold/
Share on other sites

so their a coil over?

wat are the spring rates?

how many kms been done?

are the rebuildable?

Height is adjusted via a removable c-clip that the lower spring platforms locate on not a threaded section on the shock body like most coil over units you see. The adjustments in height are limited to the notches you see machined out of the shock body unless you have more notches machined into the body.

Not sure of the spring rates. Purchased them from a jap parts importer a while ago.

I have done approx 40,000 kms on them and there is no sign of leakage.

Shocks can be rebuilt by the Australian Bilstein Distributor 'Heasman Steering' on Princess Hwy in Sydney and replacements are valued at approx $320 ea.

Link to comment
https://www.sau.com.au/forums/topic/141271-sold/#findComment-2631255
Share on other sites

are these the ones from the whiteline/bilstein group buy? they look very similar

can you get the part number off the bottom and post it up or PM me?

Edited by salad
Link to comment
https://www.sau.com.au/forums/topic/141271-sold/#findComment-2631259
Share on other sites

are these the ones from the whiteline/bilstein group buy? they look very similar

can you get the part number off the bottom and post it up or PM me?

Part numbers:

Front: F4-B46-1471-H001

Rear: F4-B46-1471-H0

Link to comment
https://www.sau.com.au/forums/topic/141271-sold/#findComment-2631325
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you flushed the initial fluid yet? It should look like a rainbow unicorn shat glitter into it. 2nd or 3rd fluid change is when you party.
    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
×
×
  • Create New...