Jump to content
SAU Community

Fs: Cefiro Bits/s13/c33/180 + Dish And Aftermarket Bits

Hella Flush
 Share

Recommended Posts

Hella Flush Experienced

Hella Flush

Posted
Posted (edited)

full 4 stud hubs brakes and stub axle setup front and rear

safety21/cusco 6 point full cage - good for street as it follows all roof and pillar lines

navy blue a31 unregistered/uncomplied 88' cefiro... factory 5 spd manual turbo... fresh 8X,XXXkm engine dropped in - gtr 33 cooler, gtr fuel pump, nismo clutch, eastbear cooler piping etc... many mods can come with it - pm for enquiry/package - has import approval so can be complied easily

fiberglass front and rear fender flares universal - arch type... with rubber seals and stainless hex bolts

random other ceffy shit... series 1 tailights with cefiro written in the middle

kei office front and rear coilovers - height and preload adjustable with front camber tops - need rear tops...

Edited by Hella Flush
NV N01 Experienced

NV N01

Posted
Posted
willing to ship thats no problems aslong as you pay for freight

It might cost a bit to send a whole car up with a cage and coilovers?

Hella Flush Experienced

Hella Flush

Posted
  • Author
Posted

photos can be found here of cage

http://i66.photobucket.com/albums/h252/1at...-10-06_12-1.jpg

http://i66.photobucket.com/albums/h252/1at...22-10-06_12.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...