Jump to content
SAU Community

Sound Gear

Nismo_Boy

By Nismo_Boy,
in Classifieds

 Share

Recommended Posts

Nismo_Boy Grand Master

Nismo_Boy

Posted
Posted

4 x Schneider 6 ½ inch coaxial 2 ways with cross overs. Model: SX-602c

Very good condition, about 2 years old, new replacement cost then wasn’t shy of $2k for the set. Crossover box’s are in good condition, some marks and chips on the plastic only.

I don’t have any specs on the speakers, so you’ll have to Google. No idea what to ask?

$600 plus postage OBO

1x Digital Designs 3515d Subwoofer (3500 series), peak power 3200, 15inch in size ect ect.

$800 plus postage OBO

These items came out of my 6000rms, 140db set up. This is what is left. None of the items have been thrashed or abused. But are in used condition.

I am in South East Queensland.

DDandSpeakers.jpg

DD.jpg

Speakers.jpg

Link to comment
https://www.sau.com.au/forums/topic/146042-sound-gear/
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...