Jump to content
SAU Community

Recommended Posts

I have been havi a problem in this hot weather with my R33 when I am in a line up or somewhere that I'm not movin long distances at a time. It's fine when I first pull up after a decent drive time. but when I'm creepin forway and raise the rev's then take my foot of the accelorator and onto the clutch the revs drop right off for a sec and sometimes even stalls.

Is this because my car is takin in hot air from the engine bay, Therfor do i need a heat sheild around the pod filter or may it be something else?

Link to comment
https://www.sau.com.au/forums/topic/150411-stallin/
Share on other sites

more likely to do with the tune at idle . some times just needs to be looked at on a dyno so I wouldnt worry about it to much until you are due for a tune etc. If it really gets anoying then a dyno would be a must.

when I had my r33gtst it had a similar problem and mark {tilbrook's}fixed it in a couple of seconds on the dyno.

Link to comment
https://www.sau.com.au/forums/topic/150411-stallin/#findComment-2801853
Share on other sites

hey its a common problem with 33's mainly its the AAC valve that gets blocked

Located at the end of your plenum fairly easy job to do

also it can be your throttle butterfly builds up with carbon so give that a clean too

you will be surprised that all it is

mike

Link to comment
https://www.sau.com.au/forums/topic/150411-stallin/#findComment-2802714
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...