Jump to content
SAU Community

Can Somone Help Me, Got Splitfires And Still Nothing


Recommended Posts

SO this is where i am up to now.

MUST READ THIS FIRST

http://www.skylinesaustralia.com/forums/in...151261&st=0

I have checked a few things and going to do alot more checking arround. BUT i got new splitfire coils, from SLIDE, and put them in and the car still misfires. I have the stock ECU with an SAFC II tuned by kutz, and all seams ok, but i still have to run .6mm gap so that it doesn't missfire, now that sux.

Can somone help me, where can i get my splitfires checked out to see if they are ok, and what else should i do?

Hay toffy, i did the folowing last night.

CAS out and tested, correct opperation and correct voltages.

Pulled out the coil loom, correct voltages, and no bad earths, all trigers correct. Coils gettign 12.4V and triger 10.2V.

All injectors correct, work as per manual, triger correctly.

Now back to 0.6mm gap and see how that goes.

I am so fed up, this sux. Sorry all sprakplugs are new too.

How did you check the injectors cobber???

I know that when my car started to miss cause of a fuel misshap when i pulled them out and got them check that 2 were knackered when they looked ok!!!

Have you check each coil indiviually to see if it just a dodgy one???

Honestly it doesn't sound like it was the stock coils giving you grief to begin with!!!

Well i haven't pulled the injectors out, just did the test in the book, voltages, resistance, and pulsed each individially, the thing is each plug looks exactly thesame, no leaning out or nothing. There are no leaks of any sought. The thing is too, it would be missfirying at the TOP aswell but it does not.

Well i am oly doing what seamed logical, i mean the coils were definatly shot, the old spark looked like something geriatric.

The car performance is definatly better, easier starts, better idle, and fuel consumption is up aswell.

I don't have the money to do much more right now, but i might have to look into the injectors.

BUT talking to KUTSI it definatly spark related as it happens at the peak cylinder pressure. So who knows. i think it's electrical, in regards to spark.

Well i haven't pulled the injectors out, just did the test in the book, voltages, resistance, and pulsed each individially, the thing is each plug looks exactly thesame, no leaning out or nothing. There are no leaks of any sought. The thing is too, it would be missfirying at the TOP aswell but it does not.

Well i am oly doing what seamed logical, i mean the coils were definatly shot, the old spark looked like something geriatric.

The car performance is definatly better, easier starts, better idle, and fuel consumption is up aswell.

I don't have the money to do much more right now, but i might have to look into the injectors.

BUT talking to KUTSI it definatly spark related as it happens at the peak cylinder pressure. So who knows. i think it's electrical, in regards to spark.

It certainly sounds electrical cobber.

You changed your ECU didn't you, do you still have the other one to try and see if that makes a difference at all???

My 33 had been playing up for a while backfireing and the engine cutting out. Thought it was to CAS but changed that and it was still doing the same thing. I finally found out the the plug that joined Haltech to the factory loom was a little loose and the connection would cut out and kill the engine.

Just something else to check.

After all that. I'd replae the old wiring loom (ignighter module to coil packs), with new fresh wires, of a larger size(there can be a performance gain as well). I'd replace your ingiter module, permanently. Then index your plugs, for height and point the gap (in the plug) at the intake valves (just mark a line on the ceramic with a texta....

Well i will check the connection plugs, but all seam preatty good, will do.

In regards to ignitor, i have a S2, and do not have it, it's inbuilt to the coils.

Does anyone have a S2 loom i can borrow overnight to have a look, i did check mine and it seamed ok, no lose conections or anyting, all good earths.

CAN YOU tell me what the plug indexing is, i think i understand, you mean point the electrode tip towards the intake valve, correct? How do you know if it is going to be the correct way in the head? ALSO what do you mean index for height?, ensure that all the plugs are the same spark gap, or hight of electrode?

SO DOES anyone have a loom i can borrow?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah that is not actually a lot. Just painting my GTR frontend and the little bits to make sideskirts/nismo flare pieces work correctly/fit on the sedan/mount up correctly came to about $7000. Is it a lot? Sure. None of this is economical. Economy would be shelling the car and buying a 2010 Corolla to commute in. The perspective of all of this is different.
    • I have the 2025 build re003s’ on my 06 XT Forester Turbo and I quite rate them for street wet and dry
    • I don't see any issues here. I've been saying all along this is a big job, the price reflects that.  When the car comes back perfect I'm sure it will feel like money well spent. 
    • Remember, take original quote. Double it. Then add a bit more. It's how any project goes.
    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
×
×
  • Create New...