Jump to content
SAU Community

Mag hitting brake caliper - how can i stop this?

Eek Skywalker

By Eek Skywalker,
in General Maintenance

 Share

Recommended Posts

Eek Skywalker Contributor

Eek Skywalker

Posted
Posted

Hello all,

my mag wheel on the left hand front side is touching the brake caliper? How can i move the caliper away from the mag? I think this is one reason why i'm getting bad vibration. I've had one suggestion to grind the mag a little on the inside, but i'm a little reluctant to do this. If I have to do this, anyone know where i can get it done?

Cheers,

Luke

p.s. the right front mag has a couple of mm's tween it and the caliper? Anyone else found this or know why the left is different to the right?

red17 Experienced

red17

Posted
Posted

They shouldnt be different, however dont grind the mag wheel back to solve the problem, shave a few mm off the caliper. Just taking the nissan lettering off will give you 2mm.

Before you attempt this get your car checked out by a professional in the suspension/wheels field, someone who can determine why its occuring. Both sides should be the same. One side doesnt have a wheel spacer on or something? Maybe someones forgot to put it back on when changing a wheel?

Red17

Demon Dave Mentor

Demon Dave

Posted
Posted

Don't shave the mag - not only will you un-balance the wheel but you could also reduce it's stuctural rigidity and that could be disasterous...:)

Either: Shave the NISSAN writing off the caliper

Or (depending on the legality of it) Use a thin wheels spacer...

Or you could get another set of wheels!:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • GTSBoy
      Blue/grey smoke after idle

      By GTSBoy · Posted

      The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • sunsetR33
      Replacing turbo water line - any recommendations or advice?

      By sunsetR33 · Posted

      One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...