Jump to content
SAU Community

Recommended Posts

Ok so an update.

Replaced all the exhaust manifold studs and new gaskets, all on the turbo side, cat seals and so forth, exhaust is leak proof.

The car still does it DAM IT. This morning it sounded like it was going to stall. I think it is fuel related. I recon a leaking fuel injector, going to have to pull them out and get checked. MORE MONEY.

I don't think it is a head gasket, as the collant we took out was clean as, and the new one is fine.

There was no oil in the water.

The hunt continues.

ALSO found with the new coolant, the car is running cooler, and there is more white froth on top of the water, but it's froth, like soap suds, and it disapears quickly. It only appeares when the car is very hot. If i take the radiator cap off, you can see the froth arround the cap, but if you turn the engine off it disapeares quickly.

DOES radiator coolant froth a bit. My dad ensures me it's not a head gasket. I have had no coolant loos or anything. LOL. Paranoid again.

Forgot to add, the car hasn't used any watter or anything, the exhaust doesn't smell sweet or anything. The car doesn't buble when hot or cold or anything like that. This only happens when the car is hot, above 80 degC. if you open the radiator cap, you can see fine bubles going past in the water, but the bubles are not air, as the radiator overflow, does not buble and the system does not get pressurised with air or anything.

Is it possible that there is some air still somwhere in the system?

I KNOW i know, stop asking so many questions.

HELP PLEASE SOMONE ANWSER ME.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...