Jump to content
SAU Community

Recommended Posts

can somone please help me, i posted a few days ago but no one seemed to know anything as there was no reply!

i have taken the bottome end of my motor apart with the head still intact on a engine stand with the intention of replacing the big end bearings and main bearings and thrust washer and the oil pump also. everything is appart. bearings have worn a little but i guess you would expet that with 100,000 kms and a heavy foot for a least 40,000 :happy:

there a no deep scores in the bearings just slight wear (coulor) and the crank looks perfect, it will be getting crack tested and the journals looked at to be positive that its fine.

my problem is that when i spoke to nissan and tried to order bearings the told me when ordering standard bearings i need to cheak markings on the crank and main and con rod caps and compare this to a chart and work out the grade i need for each bearing. they faxed me a graph but its in japanese and i cant make any sense of it.

PLEASE SOMEONE HELP ME!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/160421-rb25-engine-bearings/
Share on other sites

when you buy the acl bearings.... standard size not oversize i think its the same as nissan, they grade the bearings depending on the markings... think it may have somthing to do with balance or the exact circumference of the journal.. i dunno, all i know is when you buy a standard bearing you need to know if its a garde 1,2 or 3??

wel nissan have told me i need a grade of bearing, those markings on the front end of the crank on the conrod caps, on the side of the con rod, on your main caps.... they are there apparently for bearing grades. i know if i get the crank machined to 10thou oversize i can just order a set of 10 thou oversize bearings... but there is nothing at all wrong with my crank. anyone else have any idea?

yeah i spoke to the head mechanic of marooka nissan service and he suggested that because he couldnt tell me over the phone... said he would have to look at it. it just seems like such a pain in the arse to get it there... its all in parts... the head is still on the block... its upside down on a engine stand. plus i have to get time off work to make it there!!!

i really thought i could just pull it apart and replace the bearings like any other motor.... this SUCKS!!!!!

king bearings and linised crank for $300? so who did it and did you just send them a crank and they linish it and give you bearings that will fit?

Nepean Engines in Penrith.

took the crank to them, 2 days later got it back with new bearings and lynished . i think though that the mains are another brand not king come to mention it, as he said that the main force is on teh big ends not the main bearings, this is for a 300rwkw power goal which he knew about.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...