Jump to content
SAU Community

Recommended Posts

Hi,

I think I've already arrived at an answer for this one, but I thought I'd double check that I'm not being too harsh on this car :cheers: . In the market for a skyline, had an RACQ inspection on a 1993 GTS-T, 102'000 km (offered for $13'000). I guess I'm interested to see if the condition report is out of the ordinary or not for a skyline of this age, I'm inclined to believe it's no good (advice from friends) - I'll ring the inspector to verify my decision, and check if a compression test had been done while I'm at it. Just painful thinking ahead to how many such checks I may need to go through before I get a clean bill of health, as they're reasonably expensive :happy: . Anyway report was as follows (in summary car was rated to be in reasonable condition, with some items requiring attention). Main concern is seepage from differential.

Defects requiring attention

- Oil seepage differential centre, rear of gearbox

- No evidence of rear steer operating

- Plug missing spare tyre well (and spare tyre not present)

Other items noted

- Fluid seepage rear of clutch master cylinder

- Oil seepage lower engine

- Oil seepage air conditioning compressor

- Surface rust left sill panel seam

- Left door lock surround loose

- Scuff marks lower section from bumper bar

- Bottom of left rear guard damaged, surface rust on same

- Surface rust noted under boot areas, heavy rust left rear inner sill panel

- Sill panels / floor frames dented

- Pads worn, monitor

- Sections of exhaust system corroding, front shields, muffler in particular

- Outer tie rod ends dust boots leaking grease

- Front struts dust boots broken/loose

Any feedback would be appreciated!

On a side note, can anyone recommend a Jap performance workshop that carries out pre-sale inspections?

Thanks,

Jade.

Edited by lee81
Link to comment
https://www.sau.com.au/forums/topic/160489-buying-a-1993-skyline-gts-t/
Share on other sites

Sorry should have included that, it's an R33

Then thats easy, dont buy it :D

In all honesty it seems high price for a car that has some issues and it is the oldest of the r33's, i mean its the same age as my 32 ( I know which I'd have, haha :D ... you will never find a car that is perfect but its how many little issues you are prepared to accept. For that kind of money my mate got a mint R32 GTS-T but he did very well. I got my car a bit cheaper but its was stock as which i wanted and the paint was stone chipped etc cause the owner lived in the country, but i got a respray for $2k and got an exhaust, soon to get rims and suspension and with that I will have a car that I am very happy with. My main focus was a mechanically sound car.

To me it sounds like you need to see a few more and bring a friend, second opinions are always good. Best of luck

Edited by r32line

Thanks for the advice, that's 5/5 recommendations against (having asked friends).. damnit! :rofl:. So I'll have to look at some others, I might consider it if there's a significant drop in price, but otherwise I'll keep looking. Unforunately I'm keen on getting dark blue paintwork, and there's not nearly as many of those around as white/red/black models. I rang the inspector, he said while there is seepage he doesn't consider it a major issue to fix (causing long term drama), should just be a case of replacing the seals. Compression test had been done ('power balance' check as they list it), and results came out normal. His primary concern was rust, mostly surface rust, and one particular area around boot where it was getting a bit deep. I'm more concerned about engine condition, which he considers ok, seems it's more cosmetic issues with rust, suspects it has not been garaged (and that resale value will suffer if rust continues), as has more rust than a usual import.

Yeah like you said if it drops in price then you can consider it, but at $13,000 for a 93 model it would want to be better than it is.

The rust is a concern to me, on imports some of the cars in japan are driven in areas where it snows and they put salt on the road, this is bad news for the car as rust is a likely result. If it has already got rust arrears its not a good sign and a year later you could find it to be a lot worse.

So put all that to the seller and say at its current price it is not in your consideration, but you may consider it if its cheaper and u can spend money on it getting it all sweet.. Has it got any mods, or rims/kit/stereo? if not for $13k its quite pricey for what it is..... with the rust that is "getting a bit deep" and has your mechanic concerned then you really need to think if its worth considering at all. If so come up with a price that you would pay and be happy and then negotiate but do NOT go above that price.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1680, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
×
×
  • Create New...