Jump to content
SAU Community

Recommended Posts

Hi,

OK, my Meisters have arrived so it's time for this awsome combo to go. :dry:

Was running them on my S13.5 with 25mm wider front guards and 30mm flared rears. Being multi-stud, these will look tuff as on almost ANY ride!...

Garson DEEP DISH Racing

Specifications: (a PAIR = 2 wheels)

Size: 18x10

PCD: 4 & 5 x 114.3 (multistud)

Offset: +10

Tyres: Nankang NSII 235/40/ZR18 (75% tread)

Valve stems included

Made in Japan

Volk Racing Evolution 3

Specifications: (a PAIR = 2 wheels)

Size: 18x9

PCD: 4 & 5 x 114.3 (multistud)

Offset: +19

Tyres: Michelin Pilot Sport 225/40/ZR18 (75% tread)

Center caps and valve stems included

Made in Japan

Now I WILL seperate these into pairs, or you can simply be a man and buy all 4...

Prices as follows:

1. For ALL 4 = $1750 (Delivered Australia wide!)

2. For the 2 x Garson's = $970 (Delivered Australia wide!)

3. For the 2 x Volk Racing Evolution 3's = $820 (Delivered Australia wide!)

Cheers!

post-15856-1175049971.jpg

post-15856-1175050022.jpg

post-15856-1175050041.jpg

post-15856-1175050068.jpg

You were warned about becoming a paying trader.

And then blatantly disregarded it.

This is your LAST warning or you will be banned. No questions asked.

Thanks

You were warned about becoming a paying trader.

And then blatantly disregarded it.

This is your LAST warning or you will be banned. No questions asked.

Thanks

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...