Jump to content
SAU Community

Suspension Problem?

blinko
 Share

Recommended Posts

blinko Proficient

blinko

Posted
Posted

ok ive been hearing this noise coming from my front left suspension area for the last couple of weeks. when ever i turn my stearing wheel or go over speed bumps or pot holes it makes like a tyre tread rubbing on a plastic guard/Springy noise. it hard to explain but it kind of sounds liek a worn out mattres spring. im going to hopefully get it check out on friday, but i was just wondering what u guys think it might be just so i could get some prices ranges on fixing it.

some suggested to me that it was my suspension bushes.. does this sound correct?

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/164180-suspension-problem/
Share on other sites
BRUNSKIGTST Proficient

BRUNSKIGTST

Posted
Posted (edited)
it does have after market springs... but its not overly low... i can clear square curbs..

do u hear the noise all the time or just when u turn? maybe your tyre rubbing against the inside might need spacers or some thing, thats what im thinking but really should get checked out.

it also could not be your suspension could be your power steering also making the noise maybe those rubber bushes need to be changed.

that your looking at $300 a each one by a mechanic not too sure about price, but i think it actually is your tyre rubbing againts the guard might need wheel alignment or spacers

Edited by BRUNSKIGTST
blinko Proficient

blinko

Posted
  • Author
Posted
do u hear the noise all the time or just when u turn? maybe your tyre rubbing against the inside might need spacers or some thing, thats what im thinking but really should get checked out.

it also could not be your suspension could be your power steering also making the noise maybe those rubber bushes need to be changed.

that your looking at $300 a each one by a mechanic not too sure about price, but i think it actually is your tyre rubbing againts the guard might need wheel alignment or spacers

yeh dnt think its my tyre cause i only hear it when i am turning... but i wil turn the wheels and see if my tyres clear alright.. i hope its not expensive to fix.. :closedeyes:

BRUNSKIGTST Proficient

BRUNSKIGTST

Posted
Posted

best thing to do, if it isn't your tyre rubbing , take it to a mechanic and have the power steering checked out. Might need new Bushes, so then he will tell you the price also, and if you need spacers he will tel you how much too.

skylinegtts Experienced

skylinegtts

Posted
Posted

have a check of ur upper control arm bushes, sounds like it could be them.

if it is them, for polyurethane replacements itll cost about $140 for the bushes itself and about $180 to get them installed. the adjustable to change ur camber on the other hand which would be a better option since ur car is lowered i think goes for about $300 for the bushes not sure about install mite be more and add a wheel alignment to it aswell

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Duncan's V37.......race car?

      By Dose Pipe Sutututu · Posted

      Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • GTSBoy
      R33 persistent issues. P/steering and lag/misfire

      By GTSBoy · Posted

      What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...