Jump to content
SAU Community

Recommended Posts

ok ive been hearing this noise coming from my front left suspension area for the last couple of weeks. when ever i turn my stearing wheel or go over speed bumps or pot holes it makes like a tyre tread rubbing on a plastic guard/Springy noise. it hard to explain but it kind of sounds liek a worn out mattres spring. im going to hopefully get it check out on friday, but i was just wondering what u guys think it might be just so i could get some prices ranges on fixing it.

some suggested to me that it was my suspension bushes.. does this sound correct?

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/164180-suspension-problem/
Share on other sites

it does have after market springs... but its not overly low... i can clear square curbs..

do u hear the noise all the time or just when u turn? maybe your tyre rubbing against the inside might need spacers or some thing, thats what im thinking but really should get checked out.

it also could not be your suspension could be your power steering also making the noise maybe those rubber bushes need to be changed.

that your looking at $300 a each one by a mechanic not too sure about price, but i think it actually is your tyre rubbing againts the guard might need wheel alignment or spacers

Edited by BRUNSKIGTST
do u hear the noise all the time or just when u turn? maybe your tyre rubbing against the inside might need spacers or some thing, thats what im thinking but really should get checked out.

it also could not be your suspension could be your power steering also making the noise maybe those rubber bushes need to be changed.

that your looking at $300 a each one by a mechanic not too sure about price, but i think it actually is your tyre rubbing againts the guard might need wheel alignment or spacers

yeh dnt think its my tyre cause i only hear it when i am turning... but i wil turn the wheels and see if my tyres clear alright.. i hope its not expensive to fix.. :closedeyes:

best thing to do, if it isn't your tyre rubbing , take it to a mechanic and have the power steering checked out. Might need new Bushes, so then he will tell you the price also, and if you need spacers he will tel you how much too.

have a check of ur upper control arm bushes, sounds like it could be them.

if it is them, for polyurethane replacements itll cost about $140 for the bushes itself and about $180 to get them installed. the adjustable to change ur camber on the other hand which would be a better option since ur car is lowered i think goes for about $300 for the bushes not sure about install mite be more and add a wheel alignment to it aswell

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...