Jump to content
SAU Community

Modding My Front Lip: Cutting Fibreglass

Andi

By Andi,
in Exterior & Interior Styling

 Share

Recommended Posts

Andi Experienced

Andi

Posted
Posted

Hey guys

I've been thinking about how to go about stopping my cars frontbar/lip from stratching so much and the only solution (apart from raising the car) would be to actual mod my front lip. Now the reason I need to do this is because:

1. its too damn low obviously

2. its wasn't made for my front bar so it doesn't sit properly

3. as it doesn't sit properly its hanging lower then my skirts and doesn't line up with the kit properly

A photo has been attached to show you what I mean. So given this it looks like I have to actually CUT the parts of the lip off to get it at the right angle and height.

So my question is: what are you opinions on cutting fibreglass? What can I use to cut/remove the un-wanted parts of the fibreglass lip to the right height before I refill the gaps left over from the surgery?

post-8121-1178895567_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Nizzy_R34
      r34's love to squeal

      By Nizzy_R34 · Posted

      just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • Duncan
      Engine sputter

      By Duncan · Posted

      My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Duncan
      S1 Autech 260RS Wiring Diagrams

      By Duncan · Posted

      Awesome, thanks for sharing!
    • Duncan
      Nissan fuga 450gt android screen

      By Duncan · Posted

      To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • GTSBoy
      Nissan fuga 450gt android screen

      By GTSBoy · Posted

      So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...