Jump to content
SAU Community

Work Wheels Pre-order Happening Now! Close 22 Jun 07

JDM Concept
 Share

Recommended Posts

JDM Concept Mentor

JDM Concept

Posted
Posted

forum_header.jpg

TWO BREAKING NEWS:

1) Work Wheels has decided to revised the price of most of its range starting from June 2007 due to increase in the price of raw materials. We have revised our price as well as we are no longer able to absord the difference as they increased the price 3 times in the last 2 months! However, due to your strong aussie dollars, we are able to give 5% rebate off the advertised list in LIMITED time offer only.

so for example:

work cr kai in 18 x 9.5 +20 all round is $2350.00 but with the rebate is $2232.50 (ie less 5%)

IT APPLIES TO ALL WORK WHEELS FOR THIS SHIPMENT, OFFER MAY NOT BE VALID IN THE NEXT SHIPMENT DEPENDING ON THE YEN PRICE.

So grab the opportunity now!

2) Work emotions has added a new series called XC8 and they are available for order now! It comes with larger size of 19inch rims. Exclusive to JDM Concept as they are not even on the website as of this news release! Be the first to have them in your car in Australia or as a matter of fact in the whole world.

-----------------------------------------------------------------------------------------------------------

We are going to order new sets of rims from Work,

we would like to extend our invitation to anyone who wants to get Work Wheels to put in the same container.

Preorder close: 22 JUNE 2007 , Friday

Deposit needed: 30% of the total purchase or $500 which one is greater.

Tax invoice: given upon receiving deposit. We are registered for GST for those who want to claim as an expense.

Arrival: About 6-8 weeks from closing. Could be longer if your wheels need a lot of customising. :thumbsup:

Below is the link to work website:

WORK Wheels Website

Below is the tables of our popular work emotions (Please click each thumbnail)

WORK CR KAI

th_WORKS_CRKAI.jpg

WORK XC8

th_WORKS_XC8.jpg

WORK XD9

th_WORKS_XD9.jpg

WORK XT7

th_WORKS_XT7.jpg

For any other wheels, please send me an email at [email protected]

 Share
Go to topic listing


  • Latest Posts

    • Dose Pipe Sutututu
      RB25DE NEO with Haltech ECU

      By Dose Pipe Sutututu · Posted

      post up screen shots of your injector tables
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
    • Kinkstaah
      R34 Handbrake light saying ON and intermittently flashing

      By Kinkstaah · Posted

      This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
×
×
  • Create New...